Code No. U1195
Coding not completed
| caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be stored. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
 ).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the diagnosis code U1195 is stored in ASC-ECU, the diagnosis code may also
be stored in ETACS-ECU. When the diagnosis code is stored in ETACS-ECU, carry out the diagnosis
of the diagnosis code for ETACS-ECU first.
- When the hydraulic unit (integrated with ASC-ECU) is replaced, always carry out
the calibration of the steering wheel sensor and the G and yaw rate sensor (Refer to and ).
|
OPERATION
This diagnosis code will be stored when the variant coding for the ETACS-ECU has not been implemented.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is stored when the variant coding for ETACS-ECU has not been implemented.
PROBABLE CAUSES
- The CAN bus line is defective.
- Malfunction of the ETACS-ECU
- ETACS-ECUs have been interchanged between two vehicles.
- The ACS-ECU, which was used on another vehicle, is installed on this vehicle.
- Malfunction of the hydraulic unit assembly (integrated with ASC-ECU)
- Noise interference
|
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
|
Q.
Is diagnosis code No. U1195 stored?
|
|
|
Go to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 3. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check whether a diagnosis code is stored in the ETACS-ECU (Refer to GROUP 54A - ETACS,
Diagnosis Code Chart ).
|
|
|
Q.
Is the diagnosis code stored?
|
|
|
Follow the relevant diagnosis code procedure. Then go to Step 7.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. ETACS-ECU coding data check
|
|
|
Using M.U.T.-III, check if any abnormality is present to the coding data which are stored
in the ETACS-ECU (Refer to GROUP 00 - Coding Reference Table <Vehicles
for GCC>, <Vehicles for THAILAND>).
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 5.
|
|
|
|
|
|
Replace ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ).
Then go to Step 7.
|
|
|
|
|
|
STEP 5. Check part number of ASC-ECU
|
|
|
Check the part number of ASC-ECU.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ).
Then go to Step 7.
|
|
|
|
|
|
STEP 6. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is stored.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1195 stored?
|
|
|
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ). Then
go to Step 7.
|
|
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 7. Diagnosis code recheck.
|
|
|
Check again if the diagnosis code is stored.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1195 stored?
|
|
|
Return to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|