Code No. U1211
ENG Parity/Toggle bit error
| caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be stored. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
 ).
- Before replacing the ECU, ensure that the communication circuit is normal.
- When the hydraulic unit (integrated with ASC-ECU) is replaced, always carry out
the calibration of the steering wheel sensor and the G and yaw rate sensor (Refer to and ).
|
OPERATION
Engine-related signals are sent or received to and from between ASC-ECU and engine ECU
via CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is stored when the engine ECU has detected an abnormal engine-related
signal.
PROBABLE CAUSES
- Malfunction of ETACS-ECU
- The ASC-ECU, which was used on another vehicle, is installed on this vehicle.
- The ETACS-ECU, which was used on another vehicle, is installed on this vehicle.
- The CAN bus line is defective.
- Malfunction of engine-ECU
- Malfunction of hydraulic unit assembly (integrated with ASC-ECU)
|
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
|
Q.
Is diagnosis code No. U1211 stored?
|
|
|
Go to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 3. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check if the diagnosis code is stored in the engine ECU (Refer to GROUP 13A - Diagnosis
Code Chart ).
|
|
|
Q.
Is the diagnosis code stored?
|
|
|
Troubleshoot the engine ECU diagnosis code. Then go to Step 8.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. ETACS-ECU coding data check.
|
|
|
Using M.U.T.-III, check if any abnormality is present to the coding data which are stored
in the ETACS-ECU. (Refer to GROUP 00 - Coding Reference Table <Vehicles
for GCC>, <Vehicles for THAILAND>).
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 5.
|
|
|
|
|
|
Replace ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ).
Then go to Step 8.
|
|
|
|
|
|
STEP 5. Check part number of ASC-ECU.
|
|
|
Check if the part number of ASC-ECU.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Replace the hydraulic unit (integrated ASC-ECU) (Refer to ).
Then go to Step 8.
|
|
|
|
|
|
STEP 6. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is stored.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1211 stored?
|
|
|
Replace the engine-ECU (Refer to GROUP 13A - Engine-ECU ).
Then go to Step 7.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 7. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is stored.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1211 stored?
|
|
|
Replace the hydraulic unit (integrated with ASC-ECU) (Refer to ).
Then go to Step 8.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 8. Diagnosis code recheck.
|
|
|
Check again if the diagnosis code is stored.
|
|
|
(1)Erase the stored diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1211 stored?
|
|
|
Return to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|