Code No. U1014
FCM (CAN message) <Vehicles with FCM-LS>
| caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - Troubleshooting
 ).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit assembly (integrated with ASC-ECU) is replaced, always carry
out the calibration of the steering wheel sensor and the G and yaw rate sensor (Refer to and ).
|
OPERATION
FCM-LS related signals are sent or received to and from between ASC-ECU and FCM-ECU via
CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set when the FCM-ECU malfunction has been detected.
PROBABLE CAUSES
Current trouble
- Malfunction of FCM-LS system
- Malfunction of the laser radar (integrated with FCM-ECU)
- Malfunction of the hydraulic unit assembly (integrated with ASC-ECU)
- Noise interference
Past trouble
- Carry out diagnosis with particular emphasis on wiring harness and
connector failures between ASC-ECU and the FCM-ECU. For diagnosis procedures, refer to How to
treat past trouble. (GROUP 00 - How to Cope with Intermittent Malfunctions ).
|
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus lines (Refer to GROUP 54C - Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
|
Q.
Is diagnosis code No. U1014 set?
|
|
|
Go to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 3. Check for diagnosis codes of other systems.
|
|
|
Check if diagnosis code(s) other than U1014 is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Follow the relevant diagnosis code procedure, and then go to Step 6.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check if the diagnosis code is set in the FCM-ECU (Refer to 54A - FCM-LS, Troubleshooting ).
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Troubleshoot the FCM-ECU diagnosis code. Then go to Step 6.
|
|
|
|
|
|
Go to Step 5.
|
|
|
|
|
|
STEP 5. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Erase the set diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1014 set?
|
|
|
Replace the hydraulic unit assembly (integrated with ASC-ECU) (Refer to ). Then
go to Step 6.
|
|
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 6. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Erase the set diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U1014 set?
|
|
|
Return to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|