Code No. U0428: SAS (CAN message)
| caution |
- If there is any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
 ).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
|
OPERATION
The steering wheel sensor outputs the steering wheel status to EPS-ECU via the CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set when EPS-ECU has detected the communication error in the steering wheel sensor.
PROBABLE CAUSES
- Malfunction of the steering wheel sensor
- Malfunction of EPS-ECU
- Noise interference
|
|
STEP 1. M.U.T.-III CAN bus diagnosis
|
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus line. (Refer to GROUP 54C - CAN Bus Diagnostics Table .) On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is diagnosis code No. U0428 set?
|
|
|
Go to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 3. Check for diagnosis codes of other systems.
|
|
|
Check if diagnosis code(s) other than U0428 is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Follow the relevant diagnosis code procedure, and then go to Step 5.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. Diagnosis code recheck
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is diagnosis code No. U0428 set?
|
|
|
Replace the steering wheel sensor (Refer to GROUP 35C - Steering Wheel Sensor ). Then go to Step 5.
|
|
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 5. Diagnosis code recheck
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Erase the set diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U0428 set?
|
|
|
Replace the EPS-ECU (Refer to ). Then go to Step 6.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 6. Check whether the diagnosis code is set again.
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
|
(3)Check if the diagnosis code is set.
|
|
|
Q.
Is diagnosis code U0428 set?
|
|
|
Return to Step 1.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|