Code No. U1102: ABS timeout
caution |
- If the diagnosis code No. U1102 is set, diagnose the CAN bus lines.
- When replacing the ECU, always check that the SRS circuit is normal.
|
FUNCTION
If signal from the ABS-ECU cannot be received for 500 milliseconds or more, the SRS-ECU will set diagnosis code No. U1102.
TROUBLE JUDGEMENT
Because of the CAN-B bus circuit malfunction, if SRS-ECU becomes unable to perform the normal data transmission, SRS-ECU determines that an abnormality is present.
PROBABLE CAUSES
- Malfunction of CAN bus line
- Malfunction of ABS-ECU
- Malfunction of SRS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2
|
|
|
|
Repair the CAN bus line (Refer to GROUP 54C -
Troubleshooting ). On completion, go to Step 5.
|
|
|
|
STEP 2. Check the M.U.T.-III Diagnosis code for other systems
|
|
Check that the ABS-ECU set a diagnosis code.
|
|
Q.
Is the diagnosis code set?
|
|
Diagnose the ABS-ECU. Refer to GROUP 35B, Troubleshooting .
|
|
|
|
Go to Step 3
|
|
|
|
STEP 3. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is reset.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the ABS-ECU. After replacing the ECU, carry out the CAN bus diagnostics. Then go to Step 4.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the ABS-ECU and the SRS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 4. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is not reset.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the SRS-ECU. After replacing the ECU, carry out the CAN bus diagnostics. Then go to Step 5.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the ABS-ECU and the SRS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection Service Points -
How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
Recheck if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is reset.
|
|
Q.
Is the diagnosis code set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|