INSPECTION
PROCEDURE 2: The blower does not work
|
COMMENTS ON TROUBLE SYMPTOM
|
|
If the blower motor does not operate, the blower motor circuit system may be defective.
|
|
- Malfunction of the blower relay
- Malfunction of the blower motor
- Malfunction of the heater resister
- Malfunction of the blower switch
- Damaged wiring harness or connector
|
|
STEP 1. Check the blower relay.
|
|
Refer to .
|
|
Q.
Is the blower relay in good condition?
|
|
Go to Step 2.
|
|
|
|
Replace the blower relay.
|
|
|
|
STEP 2. Voltage measurement at blower relay connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Voltage between terminal 2, 4 and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 3. Check open circuit in blower relay line between ignition switch <Vehicles
without one touch start system> or IG2 relay <Vehicles with one touch start
system>, fusible link (6), blower relay connector and body earth.
|
|
note |
Before the wiring harness check, check the junction block connector.
|
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope
with Intermittent Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 4. Check the blower motor.
|
|
Refer to .
|
|
Q.
Is the blower motor in good condition?
|
|
Go to Step 5.
|
|
|
|
Replace the blower motor.
|
|
|
|
STEP 5. Voltage measurement at blower motor connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Voltage between terminal 1 and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 6. Check open circuit in blower motor line between blower relay
and blower motor connector.
|
|
note |
Before the wiring harness check, check the junction block connector and joint connector.
|
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope
with Intermittent Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 7. Check the heater resister.
|
|
Refer to .
|
|
Q.
Is the heater resister in good condition?
|
|
Go to Step 8.
|
|
|
|
Replace the heater resistor.
|
|
|
|
STEP 8. Check open circuit in heater resister line between blower
motor connector and heater resister connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 9. Resistance measurement at the blower switch connector.
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Continuity between terminal 4 and body earth. OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope
with Intermittent Malfunction ).
|
|
|
|
Go to Step 10.
|
|
|
|
STEP 10. Check the blower switch.
|
|
Refer to .
|
|
Q.
Is the blower switch in good condition?
|
|
Go to Step 11.
|
|
|
|
Replace the heater control panel.
|
|
|
|
STEP 11. Check open circuit in blower switch line between blower motor
connector, heater resister connector blower switch connector, and body earth.
|
|
note |
Before the wiring harness check, check the junction block connector and joint connector.
|
|
|
Q.
Is the check result normal?
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00, How to Cope
with Intermittent Malfunction ).
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|