REMOVAL AND INSTALLATION


warning For removal and installation of the passenger’s (front) air bag module, always observe the service procedures described in GROUP 52B, Driver’s and Passenger’s (Front) Air Bag Module(s) and Clock Spring .
The following bolts and screws are used for installing the instrument panel. Bolts and screws are indicated as marks shown in the illustration in the sections of "Removal and Installation" and "Disassembly and Assembly."
Name
 Symbol
 Size (D × L) mm
 Colour
 Shape
Machine flange screw
 a
 4 × 12
 Black

Tapping screw
 b
 4 × 10
 -

c
 4 × 12
 -

d
 5 × 12
 -

e
 5 × 20
 -
f
 5 × 10
 -

g
 5 × 12
 Black

h
 5 × 16
 -
Tapping screw (hexagon)
 i
 5 × 16
 -

Washer assembled screw
 j
 5 × 16
 -

k
 5 × 16
 Black

Washer assembled bolt
 l
 6 × 16
 -

m
 6 × 16
 -

caution
  • Refer to GROUP 52B-SRS Service Precautions and Driver’s and Passenger’s (Front) Air bag Module(s) and Clock Spring before removing the passenger’s (front) air bag module.
  • Do not subject the SRS-ECU to any shocks when removing or installing the instrument panel.




Removal steps


1.
 Combination meter bezel assembly


2.
 Combination meter assembly
<<A>>
3.
 Selector lever knob <A/T>


4.
 Gear shift lever knob <M/T>


5.
 Bezel <M/T>
<<B>>
6.
 Selector lever panel


7.
 Shift boot <M/T>


8.
 Hazard warning lamp switch


·
 Cowl side trim (LH) (Refer to .)
<<C>>
9.
 Glove box assembly


10.
 Glove box damper


11.
 Glove box lock


·
 Fuel filler lid lock release handle (Refer to GROUP 42, Fuel Filler Lid .)


12.
 Parcel box


13.
 Fuse box lid <L.H. drive vehicles>


14.
 Lower panel


15.
 Card holder <R.H. drive vehicles>


16.
 TCL switch <Vehicles with TCL>


17.
 Fog lamp switch


18.
 Head lamp levering switch


19.
 Remote controlled mirror switch


20.
 Cigar lighter protector <R.H. drive vehicles>


21.
 Cigar lighter <R.H. drive vehicles>


22.
 Console side cover


23.
 Ashtray


24.
 Centre console


25.
 Console bracket


26.
 Instrument centre panel


27.
 Heater control lever knob


28.
 Heater controller assembly


29.
 Inside/outside air selection switch knob


30.
 Rear window defogger switch knob


31.
 Panel


32.
 Air outlet


33.
 Accessory box assembly


34.
 Clock


35.
 Radio assembly or box assembly


36.
 Side defroster duct A


37.
 Side air outlet


38.
 Screw cap


39.
 Tray


40.
 Defroster garnish


41.
 Photo sensor


42.
 Steering column cover
<<D>>
·
 Clock spring harness connector
<<D>>
·
 Column switch harness connector
<<D>>
·
 Key reminder switch harness connector
<<D>>
·
 Ignition switch harness connector


·
 Steering column shaft (Refer to GROUP 37, Steering Shaft .)
<<D>>
·
 Passenger’s (front) air bag module (squib) harness connector


43.
 Interior temperature sensor


44.
 Instrument panel assembly

CLIP AND CLAW POSITIONS




REMOVAL SERVICE POINTS

<<A>> SELECTOR LEVER KNOB REMOVAL

Pull out the selector knob to the direction shown.

<<B>> SELECTOR LEVER PANEL REMOVAL

Open the glove box door, insert the special tool Ornament Remover (MB990784) into the shown position to remove the selector lever panel.

<<C>> GLOVE BOX ASSEMBLY REMOVAL
1.Remove the glove box screws and the glove box lamp.

2.Slide the glove box towards you to gain access to the glove box lamp wiring harness clamp. Then release the clamp to remove the glove box assembly.

<<D>> CONNECTOR DISCONNECTION
Disconnect the connectors shown in the illustration.


1.Clock spring harness connector (6)
2.Clock spring harness connector (4-Y)
3.Column switch harness connector (10)
4.Key reminder switch harness connector (9)
5.Ignition switch harness connector (6)


6. Passenger’s (front) air bag module (squib) harness connector (2-R)