Code No.B1408:
Front Impact Sensor (RH) (Squib) for Power Supply Circuit
Code No.B1409:
Front Impact
Sensor (RH) (Squib) for Communication System
![](../../../img/52/W4X52E004A00ENG.png)
caution |
If diagnosis code B1408 or B1409 is set in the
SRS-ECU, always
diagnose the CAN main bus line.
|
OPERATION
The front impact sensor includes an analogue G sensor
and CPU, etc. The CPU monitors the analogue
G sensor output signal. If the CPU judges that the front air bags should be
deployed, it sends
a fire signal to the SRS-ECU to deploy the front air bags. In addition, the
CPU diagnoses the
internal components of the front impact sensor. If a malfunction occurs, it
requests the SRS-ECU
to set a diagnosis code.
DIAGNOSIS CODE SET CONDITIONS
These diagnosis codes are set if
communication between the front impact sensor (RH) and
the SRS-ECU is not possible or faulty.
PROBABLE CAUSES
- Damaged wiring harnesses or connectors
- Malfunction of the front impact sensor (RH)
- Malfunction of the SRS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the CAN bus
lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2 .
|
|
|
|
Repair
the CAN bus line (Refer to GROUP 54F, Diagnosis ).
|
|
|
|
STEP 2. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is
set.
|
|
(1)Erase the diagnosis code.
|
|
(2)Ignition: LOCK (OFF) position to ON
|
|
(3)On completion, check that the diagnosis code is not
reset.
|
|
Q.
Is the diagnosis code set?
|
|
Go to Step 3 .
|
|
|
|
There
is an intermittent malfunction such as poor engaged connector(s) or open
circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
|
|
|
|
STEP 3. Check the front impact sensor (RH) (M.U.T.-III diagnosis
code).
|
|
(1)Disconnect the negative battery terminal.
|
|
(2)Replace the front impact sensor (RH) with the front impact
sensor (LH).
|
|
(3)Connect the negative battery terminal.
|
|
(4)Erase diagnosis code from memory, and check the diagnosis
code.
|
|
Q.
Is diagnosis code B1418 or B1419 set?
|
|
Replace the front impact sensor
(RH) with a new one (Refer to ).
Go to Step 5 .
|
|
|
|
Go to Step 4 .
|
|
|
|
STEP 4. Check the harness wires for open circuit or short circuit
between SRS-ECU connector C-119 (terminal No.47 and 48) and front impact
sensor (RH) connector
A-30 (terminal No.1 and 2).
|
![](../../../img/52/AC313404AS00ENG.png)
|
note |
After inspecting intermediate connector C-124
inspect the wiring harness. If the intermediate
connector C-124 is damaged, repair or replace it.
|
Q.
Is the check result normal?
Go to Step 5 .
Repair the harness wires between
SRS-ECU connector C-119 (terminal No.47 and 48)
and front impact sensor (RH) connector A-30 (terminal No.1 and
2).
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
Q.
Is diagnosis code B1408 or B1409 set?
|
|
Replace the SRS-ECU (Refer to ).
|
|
|
|
An
intermittent malfunction is suspected (Refer to GROUP 00, How to Use
Troubleshooting/Inspection
Service Points ).
|
|
|