Code No.B1441: Curtain air bag module (squib) (RH) system (open-circuited
in the squib circuit)
| caution |
If diagnosis code B1441 is set in the SRS-ECU, always
diagnose the CAN main bus line.
|
OPERATION
The SRS-ECU judges how severe a collision is by
detecting signals from the side impact sensors and the side-airbag safing
G-sensor. If the impact is over a predetermined level, the SRS-ECU outputs an
ignition signal. At this time, if the side-airbag safing G-sensor is on, the
curtain air bag module will deploy.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set if
curtain air bag module squib (RH) wire(s) are open-circuited.
PROBABLE CAUSES
- Improper connector contact
- Open circuit in the curtain air bag module (squib) (RH) circuit
- Malfunction of the SRS-ECU
|
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
|
Use the M.U.T.-III to diagnose the CAN bus
lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 2 .
|
|
|
|
|
|
 Repair
the CAN bus line (Refer to GROUP 54F, Diagnosis  ).
|
|
|
|
|
|
STEP 2. Check whether the diagnosis code is reset.
|
|
|
Check again if the diagnosis code is
set.
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Ignition: LOCK (OFF) position to ON
|
|
|
(3)On completion, check that the diagnosis code is not
reset.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Go to Step 3 .
|
|
|
|
|
|
There
is an intermittent malfunction such as poor engaged connector(s) or open
circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 3. Check the curtain air bag module (RH) (M.U.T.-III diagnosis
code).
|
|
|
(1)Disconnect the negative battery terminal.
|
|
(2)Disconnect curtain air bag module (RH)
connector G-04. Use a flat-tipped screwdriver to unlock the locking button
at the harness side connector by withdrawing it toward you in two stages,
and then disconnect the connector.
|
|
(3)Connect special tool dummy resistor
(MB991865) to special tool resistor harness (MB991884).
(4)Connect
special tool MB991884 to the G-04 harness side connector.
(5)Connect the
negative battery terminal.
(6)Erase diagnosis code memory, and then
check the diagnosis code.
Q.
Is diagnosis code B1441 set?
Go to Step 4 .
Replace the curtain air bag module
(RH) (Refer to ).
|
|
|
STEP 4. Resistance measurement between SRS-ECU connector C-118
(terminal No.61 and 62) and the curtain air bag module (RH) connector G-04
(terminal No.1 and 2)
|
|
(1)Disconnect SRS-ECU connector C-118 and
curtain air bag module (RH) connector G-04, and measure at the wiring
harness side. For connector G-04, use a flat-tipped screwdriver to unlock
the locking button at the harness side connector by withdrawing it toward
you in two stages, and then disconnect the connector.
|
|
(2)Connect G-04 harness side connector to
special tool resistor harness (MB991884).
|
|
(3)
| caution |
Do not insert a test probe into the terminal from
its front side directly as the connector contact pressure may be
weakened.
|
Resistance measurement between the following terminals.
- SRS-ECU connector C-118 terminal No.62 and special tool terminal
No.1
- SRS-ECU connector C-118 terminal No.61 and special tool terminal
No.2
OK: Less than 2 Ω
Q.
Are the check results normal?
Go to Step 5 .
Repair the harness wire between
SRS-ECU connector C-118 (terminal No.61and 62) and curtain air bag module
(RH) connector G-04 (terminal No.1 and 2).
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
|
Q.
Is diagnosis code No.B1441 set?
|
|
|
Replace the SRS-ECU (Refer to ).
|
|
|
|
|
|
An
intermittent malfunction is suspected (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points ).
|
|
|
|