Code No.B1447: Side Impact Sensor (Rear) (RH) Power Supply Circuit
System
| caution |
If diagnosis code B1447 is set in the SRS-ECU, always
diagnose the CAN main bus line.
|
OPERATION
The side impact sensor (Rear) includes an analogue G
sensor and CPU, etc. The CPU monitors the analogue G sensor output signal. If
the CPU judges that the curtain air bags should be deployed, it sends a fire
signal to the SRS-ECU to deploy the curtain air bags. In addition, the CPU
diagnoses the internal components of the side impact sensor (Rear). If a
malfunction occurs, it requests the SRS-ECU to set a diagnosis code.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code will set when
the power supply voltage to the side impact sensor (Rear) (RH) remains less
than a predetermined value for five seconds.
PROBABLE CAUSES
- Damaged wiring harness or connectors
- Malfunction of the side impact sensor (Rear) (RH)
- Malfunction of the SRS-ECU
|
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
|
Use the M.U.T.-III to diagnose the CAN bus
lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 2.
|
|
|
|
|
|
 Repair
the CAN bus line (Refer to GROUP 54F, Diagnosis  ).
|
|
|
|
|
|
STEP 2. Check whether the diagnosis code is reset.
|
|
|
Check again if the diagnosis code is
set.
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Ignition: LOCK (OFF) position to ON
|
|
|
(3)On completion, check that the diagnosis code is not
reset.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Go to Step 3 .
|
|
|
|
|
|
There
is an intermittent malfunction such as poor engaged connector(s) or open
circuit (Refer to GROUP 00, How to Cope with Intermittent Malfunction ).
|
|
|
|
|
|
STEP 3. Check the side impact sensor (Rear) (RH) power supply circuit.
Voltage measurement at the side impact sensor (Rear) (RH) connector
D-09.
|
|
|
(1)Disconnect the negative battery terminal.
|
|
(2)Disconnect side impact sensor (Rear) (RH)
connector D-09, and measure at the wiring harness side.
(3)Connect the
negative battery terminal.
(4)Turn the ignition switch to the "ON"
position.
|
|
(5)
| caution |
Do not insert a test probe into the terminal from
its front side directly, as the connector contact pressure may be
weakened.
|
Measure the voltage between D-09 harness side connector terminal 1
and body earth.
OK: 9 V or more
Q.
Is the check result normal?
Replace the side impact sensor
(Rear) (RH) (Refer to ). Then go to Step 5.
Go to Step
4.
|
|
|
STEP 4. Check the harness wires for open circuit or short circuit
between SRS-ECU connector C-118 (terminal No.67 and 68) and side impact
sensor (Rear) (RH) connector D-09 (terminal No.1 and 2).
|
|
Q.
Are the harness wires between SRS-ECU connector C-118 (terminal No.67 and
68) and side impact sensor (Rear) (RH) connector D-09 (terminal No.1 and
2) in good condition?
Go to Step 5.
Replace the harness wires between
SRS-ECU connector C-118 (terminal No.67 and 68) and side impact sensor
(Rear) (RH) connector D-09 (terminal No.1 and 2).
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
|
Q.
Is diagnosis code B1447 set?
|
|
|
Replace the SRS-ECU (Refer to ).
|
|
|
|
|
|
An
intermittent malfunction is suspected (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points ).
|
|
|
|