Diagnosis code No.21 Meter failure information
|
caution |
If diagnosis code No. 21 is set in the ETACS-ECU, diagnose the CAN bus lines.
|
|
|
caution |
Whenever the ECU is replaced, ensure that the input and output signal circuits are normal.
|
|
|
The ETACS-ECU receives vehicle speed-related signal from the combination meter via the CAN bus lines. If failure information is sent to the vehicle speed-related signal, diagnosis code No.21 will be set.
|
|
COMMENT ON TROUBLE SYMPTOM
|
|
Current trouble
- Connector(s) or wiring harness in the CAN bus lines, the engine-A/T-ECU <A/T> or the engine-ECU <M/T>, the combination meter, the ETACS-ECU or the output shaft speed sensor may be defective.
|
|
Past trouble
- If diagnosis code 21 is stored as a past trouble, carry out diagnosis with particular emphasis on wiring and connector(s) between the engine-A-M/T-ECU and the output shaft speed sensor. For diagnosis procedures, refer to "How to treat past trouble" (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points
).
|
|
- Malfunction of the engine-A/T-ECU
- Defective combination meter
- Malfunction of the ETACS-ECU
|
|
Step 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the CAN bus line (Refer to GROUP 54F - Troubleshooting ). Repair the CAN bus line and go to Step 6.
|
|
|
|
Step 2. M.U.T.-III diagnosis code
|
|
Check whether the combination meter-related diagnosis code is set.
|
|
Q.
Is the diagnosis code set?
|
|
Diagnose the combination meter (Refer to GROUP 54A - Troubleshooting ).
|
|
|
|
Go to Step 3.
|
|
|
|
Step 3. M.U.T.-III diagnosis code
|
|
Check if a diagnosis code, which relates to CAN communication-linked systems below, is set.
|
|
- Multi-centre display
U1113: Combination meter failure information diagnosis code
|
|
Q.
Is the diagnosis code set?
|
|
Go to Step 4.
|
|
|
|
Go to Step 5.
|
|
|
|
Step 4. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is set.
|
|
(1)Erase the diagnosis code.
|
|
(2)Ignition switch: LOCK (OFF) position to ON
|
|
(3)On completion, check that the diagnosis code is not reset.
|
|
Q.
Is the check result normal?
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the Engine-A/T-ECU and the output shaft speed sensor (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).
|
|
|
|
Replace the combination meter, and then go to Step 6 .
|
|
|
|
Step 5. Check whether the diagnosis code is reset.
|
|
Recheck if the diagnosis code is set.
|
|
(1)Erase the diagnosis code.
|
|
(2)Ignition switch: LOCK (OFF) position to ON
|
|
(3)On completion, check that the diagnosis code is not reset.
|
|
Q.
Is the check result normal?
|
|
A poor connection, open circuit or other intermittent malfunction is present in the CAN bus lines between the Engine-A/T-ECU and the output shaft speed sensor (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points ).
|
|
|
|
Replace the ETACS-ECU, and then go to Step 6.
|
|
|
|
Step 6. Check whether the diagnosis code is reset.
|
|
Recheck if the diagnosis code is set.
|
|
(1)Erase the diagnosis code.
|
|
(2)Ignition switch: LOCK (OFF) position to ON
|
|
(3)On completion, check that the diagnosis code is not reset.
|
|
Q.
Is the check result normal?
|
|
The procedure is complete.
|
|
|
|
Return to Step 1.
|
|
|