![](../../../img/11/AC904112AC00ENG.png)
|
Use special tool oil filter wrench
(MB991396, MB991828) or commercially-available tool
to remove the oil filter.
|
![](../../../img/11/AC904507AB00ENG.png)
|
Remove the oil filter stud using
recommended tool screw extractor (MB992684) or
equivalent.
note |
This recommended tool is a
component of screw extractor set
(MB992678).
|
|
|
1.Remove the oil pan
mounting bolts.
|
![](../../../img/11/AK304920AB00ENG.png)
|
2.Lightly tap special tool
oil pan FIPG cutter (MD998727) between the oil pan and the
cylinder
block. 3.Lightly tap and slide special tool to
remove the oil pan.
|
![](../../../img/11/AK901142AB00ENG.png)
|
1.
caution |
When installing the front oil
seal, be careful to avoid damage
to the front oil seal.
|
Using special tool differential oil seal installer
(MB990699), drive the oil seal so that
it is flush with the timing chain case. 2.Apply a
small amount of engine oil to the entire inner circumference
of the oil seal
lip.
|
|
1.
caution |
Sufficiently check that there
is no residual oil on the
place where degreasing is performed. If
fingerprints are left, do not touch it with bare
hands
after the degreasing, since the oils from your
fingers will harm the seal ability.
|
Remove any liquid gasket remaining on the timing
chain case, the cylinder block, and the
cylinder head.
|
![](../../../img/11/AKA00066AB00ENG.png)
|
2.Install special tool
crankshaft front oil seal guide (MB991993) onto the
crankshaft. 3.
caution |
The timing chain case should
be installed within 10 minutes
of applying liquid gasket.
|
![](../../../img/11/ACD01191AB00ENG.png) Apply
a 2 ± 0.5 mm bead of liquid gasket to location A on
the timing chain case
respectively as illustrated. (Apply a 1.75 ± 0.5 mm
wide bead in the area indicated
by *1). Apply a 1.75 ± 0.5 mm bead of liquid
gasket to location B on the timing chain
case respectively as illustrated. Specified
sealant:
A: ThreeBond 1217G or
equivalent B: ThreeBond 1227D or
equivalent
|
![](../../../img/11/ACD01192AB00ENG.png)
|
4.Install the timing chain
case.
note |
The service hole bolt and
timing chain case mounting bolts have different
lengths. Be
sure to use the correct bolt for each
location.
|
5.Tighten the service hole bolt and timing
chain case mounting bolts to the specified
torque. Tightening torque:
M6:
9.5 ± 2.5 N·m M10: 42 ± 16
N·m
|
![](../../../img/11/AKA00065AB00ENG.png)
|
1.Carefully remove the
coolant dry matters and the other foreign materials from the
O-ring
groove of the water pump. In the same way, clean the timing
chain case side. 2.Push the flange of the new
O-ring into the O-ring groove of the water pump to securely
install the O-ring. Sufficiently apply water or the coolant
to the O-ring with a brush so that the
O-ring does not fall. 3.Gently inverting the water
pump, check whether the O-ring does not
fall. 4.Install the water pump to the timing chain
case. At that time, be careful that the
O-ring does not fall or the O-ring is not jammed.
|
|
1.Remove any liquid gasket
remaining on the cylinder block, the timing chain case, the
oil seal case and the oil pan.
|
|
2.
caution |
The oil pan should be
installed within 10 minutes of applying
liquid gasket.
|
![](../../../img/11/AKB00484AB00ENG.png) Apply
a 2.5 ± 0.5 mm bead of liquid gasket to location A,
and a 4 ± 0.5
mm bead of liquid gasket to location B, and a 3 ± 0.5
mm bead of liquid gasket to location
C on the oil pan respectively as
illustrated. Specified
sealant:
ThreeBond 1217G or
equivalent
|
|
3.Install the oil pan by
tightening the fittings to the specified torque of 11
± 3
N·m.
|
|
1.Remove any liquid gasket
remaining on the cylinder head cover, the timing chain case
and the cylinder head.
|
![](../../../img/11/AK901143AB00ENG.png)
|
2.
caution |
The timing chain should be
installed within 3 minutes
of applying liquid gasket.
|
Apply a 4 mm bead of liquid gasket as
illustrated. Specified
sealant:
ThreeBond 1217G or
equivalent
|
![](../../../img/11/AKA00387AB00ENG.png)
|
3.Tighten the bolts to the
tightening torque of 2.0 ± 0.5 N·m in the order
shown in the illustration. 4.Next, tighten the
bolts to the specified torque of 7.0 ± 0.5 N·m
in the same order.
|
![](../../../img/11/AC904506AB00ENG.png)
|
Using special tool oil filter stud
setter (MB992676), install the new oil filter stud
and tighten it to the specified
torque. Specified torque: 27 ± 2
N·m
|
|
1.Clean the oil filter
installing surface on the cylinder block side.
|
![](../../../img/11/AC904113AC00ENG.png)
|
2.Apply a small amount of
engine oil to the new oil filter gasket. 3.For the
specified tightening torque, refer to the caution label
attached on the oil
filter. 4.Tighten the oil filter until the gasket
contacts with the installation surface. 5.In the
same manner as removal, use special tool oil filter wrench
(MB991396, MB991828)
or commercially-available tool to tighten the oil filter to
the specified torque.
|