Code No. P0720:
Malfunction of Output Speed Sensor
DIAGNOSTIC FUNCTION
The CVT-ECU determines whether the system is defective by monitoring the output speed
sensor.
JUDGEMENT CRITERIA
- All the conditions listed below remain for 10 seconds.
- After the selector lever is moved to the R, D, B,
S, L range, the ECU does not receive the output speed of 250 r/min or more.
- After the selector lever is moved to the R, D or B range, the ECU receives the turbine
speed of 300 r/min or less.
- The output speed is less than 150 r/min.
- The secondary pulley speed is 1,500 r/min or more.
- The output speed has dropped abruptly from 730 r/min or more to 90 r/min
or less. Then at least 0.5 seconds have passed with the reduced speed.
PROBABLE CAUSES
- Malfunction of output speed sensor
- Damaged wiring harness and connectors
- Malfunction of CVT-ECU
|
STEP 1. Check the following connector
|
|
- Output speed sensor connector
|
|
Check the terminals for a contact status problem and internal short circuit.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the defective connector.
|
|
|
|
STEP 2. Check for open circuit in SGN2 line between the output speed
sensor connector and the CVT-ECU connector
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 3. Voltage measurement at output speed sensor connector (terminal
No. 1)
|
|
(1)Disconnect the output speed sensor connector, and measure at the wiring harness
side.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between the output speed sensor connector (terminal No. 1)
and body earth. OK: 10 V or more
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
NO : Repair the connector(s) or the wiring harness (power supply line between the output
speed sensor connector terminal No. 1 and the J/B connector).
|
|
|
|
STEP 4. Check the following connector
|
|
Check the terminals for a contact status problem and internal short circuit.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the defective connector.
|
|
|
|
STEP 5. Check for open circuit or short to earth in OUTS line between
the output speed sensor connector and the CVT-ECU connector
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Repair the wiring harness.
|
|
|
|
STEP 6. Measure the output wave pattern of the output speed sensor
at CVT-ECU connector (OUTS terminal).
|
|
(1)Connect the output speed sensor connector and CVT-ECU connector.
|
|
(2)Selector lever position: D range.
|
|
(3)Drive at a constant speed of approx. 20 km/h.
|
|
(4)Connect an oscilloscope, and measure the voltage between CVT-ECU connector OUTS
terminal and body earth. OK: A wave pattern such as the one shown on (Check
Procedure Using an Oscilloscope) should be output, and the maximum value should be 11 V or more
and the minimum value should be 1 V or less. There should be no noise in the output wave pattern.
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Replace the output speed sensor.
|
|
|
|
STEP 7. Symptom recheck after erasing diagnosis code
|
|
Q.
Is the diagnosis code stored?
|
|
Replace the CVT-ECU.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions .).
|
|
|