Inspection Procedure
1: The TPMS warning lamp stays ON.
caution |
- If there is any problem in the
CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the
CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
|
OPERATION
- The TPMS warning lamp will illuminate when the tyre inflation pressure of
road wheel is below 189 kPa.
- Furthermore, the TPMS warning lamp illuminates for three seconds immediately after
the ignition switch is turned to the "ON" position. This is a bulb check of the TPMS warning
lamp.
COMMENT ON TROUBLE SYMPTOM
This may be caused by faults in the CAN bus line, combination meter or ETACS-ECU.
PROBABLE CAUSES
- Damaged wiring harness and connectors
- Low tyre inflation pressure
- Punctured tyre
- Damaged tyre valve and/or valve core
- Inaccurate tyre pressure sensor of the TPMS transmitter
- Malfunction of the combination meter
- Malfunction of the ETACS-ECU
|
STEP 1. Inspect the all tyres.
|
|
Visually check road tyres for any sign of air leak or puncture.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Replace the valve or valve core, or repair the flat tyre. Replace the tyre if
necessary. Then go to Step 2.
|
|
|
|
STEP 2. After the tyre inflation pressure is adjusted and the TPMS
transmitter sends inflation pressure information on it, check the TPMS warning lamp.
|
|
(1)Wait until the tyres cool down, and adjust road tyre inflation pressures to the
value specified on the tyre pressure label.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Drive the vehicle for five minutes.
|
|
(4)Check the TPMS warning lamp.
|
|
Q.
Is the TPMS warning lamp turned off?
|
|
The procedure is complete.
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check the tyre inflation pressure again.
|
|
Use a tyre pressure gauge to check that road tyre inflation pressures meet the value specified
on the tyre pressure label.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Replace the valve or valve core, or repair the damaged tyre. Replace the tyre
if necessary. Then return to Step 2.
|
|
|
|
STEP 4. Using M.U.T.-III, diagnose the CAN bus lines.
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
Then go to Step 5.
|
|
|
|
STEP 5. Using M.U.T.-III, read the diagnosis code.
|
|
Use M.U.T.-III to check whether diagnosis code Nos. C1912, C1922, C1932, C1942 or C1952
(Tyre air pressure low) is set.
|
|
Q.
Is diagnosis code Nos. C1912, C1922, C1932, C1942 or C1952 set?
|
|
Carry out troubleshooting for diagnosis code Nos. C1912/C1922/C1932/C1942/C1952
(Tyre air pressure low) (Refer to ).
|
|
|
|
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS-ECU) and execute "Tyre
Pressure Sensor ID Registration" on M.U.T.-III "Special Function" (Refer to ).
Then go to Step 6.
|
|
|
|
STEP 6. Check the TPMS warning lamp.
|
|
Q.
Does the TPMS warning lamp turn OFF after three seconds of initial lamp check?
|
|
Go to Step 7.
|
|
|
|
Replace the combination meter assembly (Refer to GROUP 54A - Combination
Meter Assembly). Then go to Step 7.
|
|
|
|
STEP 7. Retest the system.
|
|
Q.
Does the TPMS warning lamp turn ON and OFF normally?
|
|
The procedure is complete.
|
|
|
|
Repeat the troubleshooting from Step 1.
|
|
|