Code No. U1104: SAS
CAN timeout
caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C -
CAN Bus Diagnostics Table
).
- If diagnosis code U1104 is set in ASC-ECU, always diagnose the CAN bus line. If
there is any fault in the CAN bus lines, an incorrect diagnosis code may be set. In this case,
the set diagnosis code is not highly reliable.
- When the steering wheel sensor is replaced, always carry out calibration to make
ASC-ECU learn the neutral point (Refer to
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit (integrated with ASC-ECU) is replaced, always carry out
the calibration of the G and yaw rate sensor and the steering wheel sensor (Refer to
and ).
|
OPERATION
The ASC-ECU communicates with the steering wheel sensor via the CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
If the ACS-ECU cannot receive any signal from the steering wheel sensor for a predetermined
period, this diagnosis code will be set.
PROBABLE CAUSES
- The CAN bus line is defective.
- Malfunction of the steering wheel sensor
- Malfunction of the hydraulic unit assembly (integrated with ASC-ECU)
|
STEP 1. M.U.T.-III CAN bus diagnosis.
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus line. (Refer to GROUP 54C -
Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines.
|
|
Q.
Is diagnosis code No. U1104 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 3. Check other diagnosis codes.
|
|
Check if diagnosis code(s) other than U1104 is set.
|
|
Q.
Is the diagnosis code set?
|
|
Perform troubleshooting for the relevant diagnosis code. Then go to Step 6.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
Check whether a steering wheel sensor "time-out" related diagnosis code is set in other
ECUs.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the steering wheel sensor. (Refer to ). Then
go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
(1)Erase the set diagnosis code.
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
Q.
Is diagnosis code No. U1104 set?
|
|
Replace the hydraulic unit assembly (integrated with ASC-ECU) (Refer to ). Then
go to Step 6.
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 -
How
to Cope with Intermittent Malfunction).
|
|
|
|
STEP 6. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
(1)Erase the set diagnosis code.
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
Q.
Is diagnosis code No. U1104 set?
|
|
Return to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|