Code No.C2206: Re-execution
of variant coding
caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C -
CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When diagnosis code No.C2206 is set in ASC-ECU, the diagnosis code may also be set
in ETACS-ECU. When the diagnosis code is set in ETACS-ECU, carry out the diagnosis of the diagnosis
code for ETACS-ECU first.
- When the hydraulic unit (integrated with ASC-ECU) is replaced, always carry out
the calibration of the G and yaw rate sensor and the steering wheel sensor (Refer to
and ).
|
OPERATION
ASC-ECU receives the vehicle information stored in the ETACS-ECU via CAN bus lines.
DIAGNOSIS CODE SET CONDITIONS
The ASC-ECU compares the last vehicle information and the information before last. If
there are any differences between the two, the ECU will set this diagnosis code.
PROBABLE CAUSES
- ETACS-ECU malfunction.
- The ETACS-ECU, which was used on another vehicle, is installed on this vehicle.
- The hydraulic unit assembly (integrated with ASC-ECU), which was used on another
vehicle, is installed on this vehicle.
- Malfunction of the hydraulic unit assembly (integrated with ASC-ECU).
- Noise interference.
|
STEP 1. M.U.T.-III CAN bus diagnosis.
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus line. (Refer to GROUP 54C -
Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines.
|
|
Q.
Is diagnosis code No. C1707 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 3. Check for diagnosis codes.
|
|
Check if diagnosis code No. C1707 is also set simultaneously.
|
|
Q.
Is the diagnosis code set?
|
|
Troubleshoot for the relevant diagnosis code (Refer to ).
Then go to Step 7.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
Check whether a diagnosis code is set in the ETACS-ECU.
|
|
Q.
Is the diagnosis code set?
|
|
Follow the relevant diagnosis code procedure. (Refer to GROUP 54A -
ETACS,
Diagnosis Code Chart). Then go to Step 7.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. ETACS-ECU coding data check.
|
|
Using M.U.T.-III, check if any abnormality is present to the coding data which are stored
in the ETACS-ECU. (Refer to GROUP 00 -
Coding Reference Table ).
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Replace ETACS-ECU. (Refer to GROUP 54A -
ETACS-ECU). Then go to Step
7.
|
|
|
|
STEP 6. Diagnosis code recheck.
|
|
Check again if the diagnosis code is set.
|
|
(1)Erase the set diagnosis code.
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
Q.
Is diagnosis code No. C2206 set?
|
|
Replace the hydraulic unit assembly (integrated with ASC-ECU) (Refer to ).
Then go to Step 7.
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 -
How
to Cope with Intermittent Malfunction).
|
|
|
|
STEP 7. Diagnosis code recheck.
|
|
Check again if the diagnosis code is set.
|
|
(1)Erase the set diagnosis code.
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
Q.
Is diagnosis code No. C2206 set?
|
|
Return to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|