Code No. U0402: T/M
(CAN message)
| caution |
- If there is any
problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C -
CAN Bus Diagnostics Table
 ).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the hydraulic unit (integrated with ASC-ECU) is replaced, always carry out
the calibration of the G and yaw rate sensor and the steering wheel sensor (Refer to and ).
|
OPERATION
CVT-related signals are sent or received between the ASC-ECU and the CVT-ECU via CAN bus
lines.
DIAGNOSIS CODE SET CONDITIONS
This diagnosis code is set when the CVT-ECU malfunction has been detected.
PROBABLE CAUSES
- CVT-related malfunction
- The CVT-ECU is defective.
- Malfunction of the hydraulic unit assembly (integrated with ASC-ECU)
- Noise interference
|
|
STEP 1. M.U.T.-III CAN bus diagnosis.
|
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 3.
|
|
|
|
|
|
 Repair the CAN bus line. (Refer to GROUP 54C -
Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines.
|
|
|
Q.
Is diagnosis code No. U0402 set?
|
|
|
Go to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 3. Check for diagnosis codes of other systems.
|
|
|
Check if diagnosis code(s) other than U0402 is stored.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Follow the relevant diagnosis code procedure, and then go to Step 6.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check if the diagnosis code is set in the CVT-ECU.
|
|
|
Q.
Is the diagnosis code stored?
|
|
|
Follow the relevant diagnosis code procedure (Refer to GROUP 23A -
Diagnosis
Code Chart ). Then go to Step 6.
|
|
|
|
|
|
Go to Step 5.
|
|
|
|
|
|
STEP 5. Diagnosis code recheck.
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Erase the set diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U0402 set?
|
|
|
Replace the hydraulic unit assembly (integrated with ASC-ECU) (Refer to ).
Then go to Step 6.
|
|
|
|
|
|
The trouble can be an intermittent malfunction. (Refer to GROUP 00 -
How
to Cope with Intermittent Malfunction).
|
|
|
|
|
|
STEP 6. Diagnosis code recheck.
|
|
|
Check again if the diagnosis code is set.
|
|
|
(1)Erase the set diagnosis code.
|
|
|
(2)Ignition switch: "LOCK" (OFF)
|
|
|
Q.
Is diagnosis code No. U0402 set?
|
|
|
Return to Step 3.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|