Code No.C1511:
Torque sensor main
Code No.C1512: Torque sensor sub
caution |
- If there is any problem in the
CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the
CAN bus lines (Refer to GROUP 54C, CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
|
OPERATION
Power is supplied to the torque sensor from the EPS-ECU.
DIAGNOSIS CODE SET CONDITIONS
These diagnosis codes are set in the following cases:
C1511: Torque sensor main system malfunction
- The torque sensor main output voltage does not agree with the predetermined voltage
stored in the microcomputer, and the microcomputer determines that a problem has occurred in
the torque sensor main system.
C1512: Torque sensor sub system malfunction
- The torque sensor sub output voltage does not agree with the predetermined voltage
stored in the microcomputer, and the microcomputer determines that a problem has occurred in
the torque sensor sub system.
PROBABLE CAUSES
- Malfunction of CAN bus line
- Defective torque sensor of the steering column shaft assembly
- Defective harness wire(s) or connector(s)
- Short or open circuit between the EPS-ECU and the torque sensor or loose
connector contact
- Malfunction of the EPS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code C1511 or C1512 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 3. Check the following connector.
|
|
Check the connectors below for improper engagement, terminal damage or terminal drawn
in the connector case.
|
|
- EPS-ECU connector
- Torque sensor intermediate connector of the wiring harness for steering column shaft
assembly (connection and appearance checks only)
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 4. Wiring harness check
|
|
(1)Check the wiring harness between the EPS-ECU connector terminal TSM and the torque
sensor main for damage or other problem.
|
|
(2)Check the wiring harness between the EPS-ECU connector terminal TSS and the torque
sensor sub for damage or other problem.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 5. Voltage measurement at the EPS-ECU connector
|
|
(1)The steering is in the neutral position.
|
|
(2)Measure the EPS-ECU voltage without disconnecting the connector (by backprobing).
|
|
(3)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(4)Measure the voltage between the EPS-ECU connector terminal TSM (for main system)
and the EPS-ECU connector terminal GND. OK: Approximately 2.5 V
|
|
(5)Measure the voltage between the EPS-ECU connector terminal TSS (for sub system)
and the EPS-ECU connector terminal GND. OK: Approximately 2.5 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 6. M.U.T.-III data list
|
|
(1)The steering is in the neutral position.
|
|
(2)Check the following data list (Refer to ).
- Item No. 01: Torque sensor (main)
- Item No. 02: Torque sensor (sub)
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Check whether the diagnosis code is set again.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code C1511 or C1512 set?
|
|
Replace the EPS-ECU (Refer to ). Then go to Step
8.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ). Then go to Step 8.
|
|
|
|
STEP 8. Check whether the diagnosis code is set again.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code C1511 or C1512 set?
|
|
Replace the steering column shaft assembly (Refer to ).
Then go to Step 9.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
STEP 9. Check whether the diagnosis code is set again.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is diagnosis code C1511 or C1512 set?
|
|
Return to Step 1.
|
|
|
|
This diagnosis is complete.
|
|
|