Inspection Procedure
4: The windshield wipers do not work normally.
| caution |
Whenever the ECU is replaced,
ensure that the input and output signal circuits are normal.
|
COMMENTS ON TROUBLE SYMPTOM
The windshield wiper motor, the column switch or ETACS-ECU may be defective.
PROBABLE CAUSES
- Malfunction of the windshield wiper motor
- Malfunction of the column switch
- The ETACS-ECU may be defective
- Damaged harness wires and connectors
|
|
STEP 1. M.U.T.-III diagnosis code.
|
|
|
Check if an ETACS-related diagnosis code is set.
|
|
|
Q.
Is the diagnosis code set?
|
|
|
 Diagnose the ETACS (Refer to GROUP 54A -
ETACS, Trouble Symptom Chart  ).
|
|
|
|
|
|
 Go to Step 2.
|
|
|
|
|
|
STEP 2. M.U.T.-III data list
|
|
|
Check the input signal related to the windshield wiper operation.
|
|
|
- Ignition switch: ACC
- Operate the windshield wiper switch.
|
|
|
Item No.
|
Item name
|
Normal conditions
|
Item 65
|
Front wiper output
|
ON
|
Item 66
|
Front wiper HI output
|
ON
|
|
|
|
OK: Normal condition is displayed.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 3.
|
|
|
|
|
|
Refer to GROUP 54A -
ETACS, Inspection Procedure 9 "The column switch
signal is not received"? Refer to .
|
|
|
|
|
|
STEP 3. Check that the windshield wipers work.
|
|
|
Check that the windshield wipers work at high speed and the mist mode.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 4.
|
|
|
|
|
|
Go to Step 7.
|
|
|
|
|
|
STEP 4. Check the windshield wiper motor.
|
|
|
Check that the windshield wiper motor works normally (Refer to ).
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 5.
|
|
|
|
|
|
Replace the windshield wiper motor.
|
|
|
|
|
|
STEP 5.Check of open, short circuit in F/WIP LO line between windshield
wiper motor connector and ETACS-ECU connector
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
|
|
Check that the windshield wipers work normally by moving the switch to each position.
|
|
|
Q.
Is the check result normal?
|
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Use Troubleshooting/Inspection
Service Points, -
How to Cope with Intermittent Malfunctions ).
|
|
|
|
|
|
Replace the ETACS-ECU.
|
|
|
|
|
|
STEP 7. Check the windshield wiper motor.
|
|
|
Check that the windshield wiper motor works normally (Refer to ).
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 8.
|
|
|
|
|
|
Replace the windshield wiper motor.
|
|
|
|
|
|
STEP 8. Measure the voltage at windshield wiper motor connector.
|
|
|
(1)Disconnect the connector, and measure the voltage at the wiring harness side.
|
|
|
(3)Windshield wiper switch: HI
|
|
|
(4)Measure the voltage between the windshield wiper motor connector power supply terminal
and the body earth.
OK: System voltage
|
|
|
Q.
Is the check result normal?
|
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Use Troubleshooting/Inspection
Service Points, -
How to Cope with Intermittent Malfunctions ).
|
|
|
|
|
|
Go to Step 9.
|
|
|
|
|
|
STEP 9. Check of open, short circuit in F/WIP HI line between windshield
wiper motor connector and ETACS-ECU connector.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 10.
|
|
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
|
|
Check that the windshield wipers work normally by moving the switch to each position.
|
|
|
Q.
Is the check result normal?
|
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Use Troubleshooting/Inspection
Service Points, -
How to Cope with Intermittent Malfunctions ).
|
|
|
|
|
|
Replace the ETACS-ECU.
|
|
|
|