INSPECTION PROCEDURE
2: Power supply circuit system
|
To SRS-ECU, the power is supplied from two independent circuits (fuse No. 15 and 21) via
ignition switch (IG1) <vehicles without keyless operation system> or IG1 relay <Vehicles
with keyless operation system>.
|
|
If the power is not supplied to SRS-ECU, the communication between M.U.T.-III and SRS-ECU
cannot be established.
|
|
- Damaged wiring harness and connectors
- Battery failure
- Malfunction of the charging system
- Malfunction of SRS-ECU
|
|
STEP 1. Fuse Nos. 15, 21 check.
|
|
Q.
Is the fuse in good condition?
|
|
Go to Step 3.
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Fuse open circuit check
|
|
(2)Turn the ignition switch to the "ON" position, wait for at least one minute, and
then turn the switch "LOCK" (OFF).
|
|
Q.
Is the fuse in good condition?
|
|
Go to Step 3.
|
|
|
|
Repair the wiring harness IG1A line between the junction block connector and SRS-ECU
connector, IG1B line between the junction block connector terminal No. 8 and the SRS-ECU connector,
and replace the fuse.
|
|
|
|
STEP 3. Resistance measurement at the SRS-ECU connector.
|
|
(1)Disconnect the SRS-ECU connectors.
|
|
(2)Take the measurements below at the wiring harness side connectors.
- Continuity GND1 line between wiring harness side connector
and body earth
OK: Continuity (less than 2 Ω)
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the wiring harness GND1 line between the SRS-ECU connector and the body
earth.
|
|
|
|
STEP 4. Voltage measurement at the SRS-ECU connector (IG1A, IG1B line).
|
|
(1)Check that the negative battery terminal is disconnected. If the negative battery
terminal is connected, disconnect it.
|
|
(2)Disconnect the SRS-ECU connector.
|
|
(3)Connect the negative battery terminal.
|
|
(5)Take the measurements below at the harness side connector.
- Voltage IG1A, IG1B line between the SRS-ECU connector
and the body earth
OK: 9 V or more
|
|
(6)Disconnect the negative battery terminal.
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Resistance measurement at the SRS-ECU connector (IG1A, IG1B
line).
|
|
(1)Check that the negative battery terminal is disconnected. If the negative battery
terminal is connected, disconnect it.
|
|
(2)Disconnect the SRS-ECU connector.
|
|
(3)
- Continuity IG1A line between junction block connector and
SRS-ECU connector
- Continuity IG1B line between junction block connector and SRS-ECU connector
OK: Continuity (less than 2 Ω)
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Repair the wiring harness IG1A line between the junction block connector and the
SRS-ECU connector, IG1B line between the junction block connector and SRS-ECU connector.
|
|
|
|
STEP 6. Trouble symptom check.
|
|
Q.
Is the communication between M.U.T.-III and SRS-ECU possible?
|
|
Intermittent malfunction.
|
|
|
|
Replace SRS-ECU.
|
|
|