Code No.B1610
Seat belt pre-tensioner (passenger’s side) (squib) system (open circuit
of squib circuit)
caution |
If diagnosis code No. B1610
is stored in the SRS-ECU, be sure to diagnose the CAN bus line.
|
OPERATION
Only when the frontal impact exceeding the threshold is
simultaneously detected (turned
ON) by the front impact sensor as well as by the analogue G-sensor in SRS-ECU,
the electric
current is supplied from SRS-ECU to the seat belt pre-tensioner (squib).
TROUBLE JUDGEMENT
The code is stored when the open circuit occurs
to the SRS-ECU seat belt pre-tensioner (passenger’s
side) (squib) circuit.
PROBABLE CAUSES
- Damaged wiring harness and connector
- Open circuit to seat belt pre-tensioner (passenger’s side) (squib)
circuit
- Malfunction of SRS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics.
|
|
Use M.U.T.-III to diagnose the CAN bus
lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair
the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
|
|
|
|
STEP 2. Check whether the diagnosis code is stored again.
|
|
(1)Connect the negative battery terminal.
|
|
(2)After erasing the diagnosis code memory, check the
diagnosis code again.
|
|
(3)Disconnect the negative battery terminal.
|
|
Q.
Is diagnosis code No. B1610 stored?
|
|
Go to Step 3.
|
|
|
|
Intermittent malfunction (Refer to
GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|
|
STEP 3. Diagnosis check by dummy resistor connection.
|
|
(1)Check that the negative battery terminal is disconnected.
If the negative battery
terminal is connected, disconnect it.
|
![](../../../img/52/ACB04317AB00ENG.png)
|
(2)Use the flat-tipped screwdriver to pull out
the locking button of harness side connector.
After releasing the lock, disconnect the seat belt pre-tensioner
(passenger’s side) harness
side connector.
|
![](../../../img/52/AC301553DP00ENG.png)
|
(3)Connect special tool dummy resistor
(MB991865) to special tool resistor harness (MB991884). (4)Connect
special tool resistor harness to the seat belt pre-tensioner
(passenger’s
side) harness side connector. (5)Connect the negative battery
terminal. (6)After erasing the diagnosis code memory, check the
diagnosis code again. (7)Disconnect the negative battery
terminal.
Q.
Is diagnosis code No. B1610 stored?
Go to Step 4.
Replace the seat belt with
pre-tensioner (passenger’s side) (Refer to ).
|
|
STEP 4. Resistance measurement at the SRS-ECU connector and the seat
belt pre-tensioner (passenger’s side) connector.
|
|
(1)Check that the negative battery terminal is disconnected.
If the negative battery
terminal is connected, disconnect it.
|
![](../../../img/52/AC905015AC00ENG.png)
|
(2)While pushing the part "A" indicated in the
figure of the harness side connector, turn
the lock lever to the direction of the arrow to release the lock lever, and
disconnect the SRS-ECU
connector.
|
![](../../../img/52/ACB04317AB00ENG.png)
|
(3)
danger |
To release the SRS-ECU connector short spring in
the
following operations, disconnect this seat belt pre-tensioner connector,
and keep the squib
circuit shorted.
|
Use the flat-tipped screwdriver to pull out the locking button of
harness side connector.
After releasing the lock, disconnect the seat belt pre-tensioner
(passenger’s side)
harness side connector.
|
![](../../../img/52/AC905468AQ00ENG.png)
|
(4)
caution |
The short spring may not be released due to the
insufficient insertion. Therefore, insert
the insulator for 4 mm or more.
|
Insert an insulator (width: 3 mm, thickness: 0.5 mm) such as cable
tie between the PTA+,
PTA- line, and the short spring, and release the short spring.
|
![](../../../img/52/AC201287GJ00ENG.png)
|
(5)Connect special tool resistor harness
(MB991884) to the removed seat belt pre-tensioner
(passenger’s side) harness side connector. (6)Take the
measurements below at the resistor harness and SRS-ECU harness side
connector.
- Continuity PTA+ line between SRS-ECU connector
and resistor harness connector
- Continuity PTA- line between SRS-ECU connector to resistor harness
connector
OK: Continuity (less than 2 Ω)
Q.
Is the check result normal?
Go to Step 5.
Repair the wiring harness PTA+,
PTA- line between the SRS-ECU connector
and the seat belt pre-tensioner (passenger’s side)
connector.
|
|
STEP 5. Check whether the diagnosis code is stored again.
|
|
Q.
Is diagnosis code No. B1610 stored?
|
|
Replace SRS-ECU (Refer to SRS-ECU ).
|
|
|
|
Intermittent malfunction (Refer to
GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction ).
|
|
|