Tool
|
Number
|
Name
|
Use
|
|
MB992080
|
Belt tension meter
set
a: Belt tension meter b: Microphone
assembly
|
Drive belt tension
check
|
|
MB991955
a: MB991824 b:
MB991827 c: MB991910 d: MB991911 e:
MB991825 f: MB991826
|
M.U.T.-III sub
assembly
a: Vehicle communication
interface (V.C.I.) b: M.U.T.-III USB cable c:
M.U.T.-III main harness A (Vehicles with CAN
communication system) d: M.U.T.-III main harness B
(Vehicles without CAN communication system) e:
M.U.T.-III measurement adapter f: M.U.T.-III trigger
harness
|
caution |
For vehicles with CAN
communication, use M.U.T.-III main harness A to
send simulated vehicle speed. If you connect
M.U.T.-III main harness B instead, the CAN
communication does not function
correctly.
|
- Checking the idle speed
- Erasing diagnosis code
|
|
MB992188
|
Fuel injection pipe
wrench
|
Removal and
installation of fuel injection pipe assembly
|
|
MB992852
- Spare part: MB992872
|
Valve adjusting
feeler gauge
- Spare part: Feeler gauge tip set (0.14
mm)
|
Check and
adjustment of inlet valve clearance
|
|
MB991477
|
Valve adjusting
socket
|
Adjustment of inlet
valve clearance
|
|
MB992046
|
Valve adjusting
socket
|
Adjustment of
exhaust valve clearance
|
|
MB992285
|
Compression press
test adapter
|
Measurement of
compression pressure
|
|
MB992276
|
Drive belt
remover
|
Water pump drive
belt removal
|
|
MB990767
|
Front hub and
flange yoke holder
|
Holding the
crankshaft pulley
|
|
MD998754
|
Pin
|
|
MB991956
|
Engine hanger
plate
|
Supporting the engine
and transmission assembly
note |
Special tool MB991454 is a
part of engine hanger attachment set
MB991453.
|
|
|
MB991454
|
Engine hanger
balancer
|
|
MB991527
|
Hanger
|
|
MB991895
|
Engine
hanger
|
When the engine
hanger is used: Supporting the engine assembly during
removal and installation of the crankshaft pulley, timing
chain case assembly or transmission assembly
|
|
MB991928
a: MB991929 b:
MB991930 c: MB991931 d: MB991932 e:
MB991933 f: MB991934
|
Engine
hanger
a: Joint (50) × 2 b: Joint
(90) × 2 c: Joint (140) × 2 d: Foot
(standard) × 4 e: Foot (short) × 2 f:
Chain and hook assembly
|
|
MB992288
|
Drive belt
installer
|
Water pump drive
belt installation
|
|
MB992289
|
Injector and fuel
pipe remover
|
Fuel injector and
common rail assembly removal
|
|
MB992333
|
Nozzle gasket
remover
|
Fuel injection
nozzle gasket removal
|
|
MB991614
|
Angle
gauge
|
Fuel injector
holder bolt installation
|
|
MD998772
|
Valve spring
compressor
|
Valve spring
compression
|
|
MB992090
|
Retainer holder
attachment
|
|
MB992283
|
Retainer holder
D
|
|
MB992085
|
Valve stem seal
pliers
|
Valve stem seal
removal
|
|
MH062687
|
Installer inlet
ring
|
Crankshaft
rotation
|
|
MD998775
|
Valve stem seal
installer
|
Valve stem seal
press-fitting <exhaust side>
|
|
MB992284
|
Valve stem seal
installer
|
Valve stem seal
installation <inlet side>
|
|
MD998727
|
Oil pan FIPG
cutter
|
Engine oil pan
removal
|
|
MD998781
|
Flywheel
stopper
|
Supporting the
drive plate
|
|
MB991818
|
Oil seal
installer
|
Crankshaft rear oil
seal installation
|
|
MB990938
|
Installer
bar
|
|
MB992290
|
Oil seal
installer
|
Crankshaft front oil
seal installation
|
|
MB992075
|
Handle
|