Tool
|
Number
|
Name
|
Use
|
![](../../../img/11/MB992080AF00ENG.png)
|
MB992080 a: MB992081 b:
MB992082
|
Belt
tension meter set a: Belt tension meter b:
Microphone assembly
|
Alternator and
others belt tension check
|
![](../../../img/11/ACB05421AB00ENG.png)
|
- MB992744
- MB992745
- MB992746
- MB992747
- MB992748
|
- Vehicle communication interface-Lite
(V.C.I.-Lite)
- V.C.I.-Lite main harness A (for vehicles
with CAN communication)
- V.C.I.-Lite main harness B (for vehicles
without CAN communication)
- V.C.I.-Lite USB cable short
- V.C.I.-Lite USB cable long
|
- Checking the ignition timing
- Checking the idle speed
|
![](../../../img/11/MB991955AN00ENG.png)
|
MB991955
a: MB991824 b:
MB991827 c: MB991910 d: MB991911 e:
MB991825 f: MB991826
|
M.U.T.-III sub
assembly
a: Vehicle communication
interface (V. C. I.) b: M.U.T.-III USB cable c:
M.U.T.-III main harness A (Vehicles with CAN
communication system) d: M.U.T.-III main harness B
(Vehicles without CAN communication system) e:
M.U.T.-III adapter harness f: M.U.T.-III trigger
harness
|
caution |
For vehicles with CAN
communication,
use M.U.T.-III main harness A to send simulated
vehicle speed. If you connect M.U.T.-III main
harness
B instead, the CAN communication does not
function correctly.
|
- Checking the ignition timing
- Checking the idle speed
|
![](../../../img/11/MB990767AA00ENG.png)
|
MB990767
|
Front hub and
flange yoke holder
|
Holding the
crankshaft pulley
|
![](../../../img/11/MD998719AA00ENG.png)
|
MD998719
|
Pin
|
![](../../../img/11/MB992103AA00ENG.png)
|
MB992103
|
Chain tension
release bar
|
Camshaft and
camshaft sprocket assembly (exhaust side) removal
|
![](../../../img/11/AC211874AA00ENG.png)
|
MD998772
|
Valve spring
compressor
|
Valve spring
compression
|
![](../../../img/11/MB992090AA00ENG.png)
|
MB992090
|
Retainer holder
attachment
|
![](../../../img/11/MB992089AA00ENG.png)
|
MB992089
|
Retainer holder
C
|
![](../../../img/11/MB992085AA00ENG.png)
|
MB992085
|
Valve stem seal
pliers
|
Valve stem seal
removal
|
![](../../../img/11/MD998737AA00ENG.png)
|
MD998737
|
Valve stem seal
installer
|
Valve stem seal
press-fitting
|
![](../../../img/11/MD998727AA00ENG.png)
|
MD998727
|
Oil pan FIPG
cutter
|
Engine oil pan
removal
|
![](../../../img/11/MB991883AA00ENG.png)
|
MB991883
|
Flywheel
stopper
|
Supporting the
drive plate
|
![](../../../img/11/MD998718AA00ENG.png)
|
MD998718
|
Crankshaft rear oil
seal installer
|
Press-fitting the
crankshaft rear oil seal
|
![](../../../img/11/MB991448AA00ENG.png)
|
MB991448
|
Bush remover and
installer base
|
Press-fitting the
crankshaft front oil seal
|
![](../../../img/11/MB991614AA00ENG.png)
|
MB991614
|
Angle
gauge
|
Balancer shaft and
oil pump module bolt installation
|
![](../../../img/11/MB991454AA00ENG.png)
|
MB991454
|
Engine hanger
balancer
|
Support of engine
assembly
note |
- For the engine hanger balancer
(MB991454), use a chain only.
- Engine hanger balancer (MB991454) is a
part of the engine hanger assembly
(MB991453).
|
|
![](../../../img/11/MB991527AA00ENG.png)
|
MB991527
|
Hanger
|
![](../../../img/11/MB991928AI00ENG.png)
|
MB991928
a: MB991929 b:
MB991930 c: MB991931 d: MB991932 e:
MB991933 f: MB991934
|
Engine
hanger
a: Joint (50) × 2 b: Joint
(90) × 2 c: Joint (140) × 2 d: Foot
(standard) × 4 e: Foot (short) × 2 f:
Chain and hook assembly
|
![](../../../img/11/MZ203830AA00ENG.png)
|
MB991895
|
Engine
hanger
|
![](../../../img/11/MB991956AA00ENG.png)
|
MB991956
|
Engine hanger
plate
|
![](../../../img/11/MB992853AA00ENG.png)
|
MB992853
|
Engine hanger
plate
|