Inspection Procedure 17: Battery Run Down
COMMENTS ON TROUBLE SYMPTOM
- The exciting currents of the alternator field coil are input into the engine-ECU connector terminal ALTL from the alternator connector terminal.
- The electric generating capacity of the alternator connector terminal is restricted according to the signal from the engine-ECU connector terminal ALTG
COMMENTS ON TROUBLE SYMPTOM
- Failure is possibly caused by failed alternator or alternator control system.
PROBABLE CAUSES
- Failed battery
- Short circuit in alternator G terminal
- Failed alternator
- Failed engine-ECU
|
|
- Check battery (Refer to GROUP 54A - Battery - On-vehicle Service - Battery Test
 ).
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 2.
|
|
|
|
|
|
 Replace the battery.
|
|
|
|
|
|
STEP 2. M.U.T.-III diagnosis code
|
|
|
Q.
Is diagnosis code stored?
|
|
|
Inspection chart for diagnosis code (Refer to ).
|
|
|
|
|
|
Go to Step 3.
|
|
|
|
|
|
STEP 3. Voltage measurement at alternator connector (ALTL line).
|
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
|
(3)Check the voltage between the alternator connector (ALTL line) and body earth.
OK: System voltage
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Go to Step 4.
|
|
|
|
|
|
STEP 4. Check of short to earth, and open circuit in ALTL line between engine-ECU connector and alternator connector.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 5.
|
|
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
|
|
STEP 5. Check the trouble symptom.
|
|
|
Q.
Does the trouble symptom persist?
|
|
|
Replace the engine-ECU.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
|
|
STEP 6. Check of harness damage in ALTL line between engine-ECU connector and alternator connector.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 7.
|
|
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
|
|
STEP 7. Voltage measurement at alternator connector (ALTG line).
|
|
|
(1)Disconnect the connector, and measure at the alternator side.
|
|
|
(2)Connect special tool Test Harness (MB991658) to all terminals except the alternator connector (ALTG line).
|
|
|
(4)Check the voltage between the alternator connector (ALTG line) and body earth.
OK: System voltage
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 8.
|
|
|
|
|
|
Replace the alternator.
|
|
|
|
|
|
STEP 8. Check of short circuit to earth in ALTG line between alternator connector and engine-ECU connector.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 9.
|
|
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
|
|
STEP 9. Voltage measurement at engine-ECU connector (ALTG terminal).
|
|
|
(1)Disconnect engine-ECU connector, and connect special tool power plant ECU check harness (MB992110) to measure at connector for inspection.
|
|
|
(2)Engine: Idle operation after warm-up
|
|
|
(4)Cooling fan: Not operated
|
|
|
(5)Check the voltage between the engine-ECU connector (ALTG terminal) and body earth.
OK: The voltage increases when the headlamp switch and the rear window defogger switch are turned ON from OFF.
|
|
|
Q.
Is the check result normal?
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
|
|
Go to Step 5.
|
|
|
|