Code No. P0340: Camshaft Position Sensor System
OPERATION
- Power is supplied to the camshaft position sensor from the engine-ECU connector terminal 5V and is earthed to the engine-ECU connector terminal SGCE from the camshaft position sensor.
- A power voltage of 5 V is applied to the camshaft position sensor output terminal from the engine-ECU connector terminal SGC.
FUNCTION
- The camshaft position sensor detects the top dead centre on the compression stroke of the No. 1 cylinder and inputs a pulse signal to the engine-ECU.
TROUBLE JUDGEMENT
Check Condition, Judgement Criterion
- Normal signal pattern has not been input for cylinder identification from the crankshaft position sensor signal and camshaft position sensor signal for 2 seconds.
Check Condition
- Engine speed is more than 500 r/min.
- Engine is being cranked.
Judgement Criterion
- Camshaft position sensor output voltage has not changed (no pulse signal is input) for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
- Engine runs in learned pattern until engine stops.
- Does not restart the engine after it is stopped once.
- Does not control variable valve timing (V.V.T.).
- Does not operate the MIVEC in high-speed mode.
PROBABLE CAUSES
- Failed camshaft position sensor
- Open/short circuit or harness damage in camshaft position sensor circuit or loose connector contact
- Failed engine-ECU
|
STEP 1. Voltage measurement at camshaft position sensor connector (SGC line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(3)Check the voltage between the camshaft position sensor connector (SGC line) and body earth. OK: 4.9 - 5.1 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Check of short to power supply, short to earth and open circuit in SGC line between camshaft position sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 3. M.U.T.-III diagnosis code
|
|
- Reconfirmation of diagnosis code.
|
|
Q.
Is the diagnosis code stored?
|
|
Replace the engine-ECU.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 4. Voltage measurement at camshaft position sensor connector (5V line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(3)Check the voltage between the camshaft position sensor connector (5V line) and body earth. OK: System voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Check of short circuit to earth and open circuit in 5V line between camshaft position sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 6. Resistance measurement at camshaft position sensor connector (SGCE line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Check the resistance between the camshaft position sensor connector (SGCE line) and body earth. OK: Continuity (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Check of open circuit and damage in SGCE line between camshaft position sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 8. Perform output wave pattern measurement at camshaft position sensor connector (Using an oscilloscope).
|
|
(1)Use special tool test harness (MB991709) to connect connector, and measure at pick-up harness.
|
|
(4)Check the voltage between the camshaft position sensor connector (SGC line) and body earth. OK: Waveforms should be displayed on inspection procedure using an oscilloscope (Refer to ), its maximum value should be 4.8 V or more, and its minimum value should be 0.6 V or less. There must be no noise in the output wave pattern.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Go to Step 9.
|
|
|
|
STEP 9. Check of harness damage in 5V line between camshaft position sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 10.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 10. Check of harness damage in SGC line between camshaft position sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 11.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 11. Check camshaft sensing cylinder.
|
|
Q.
Is the check result normal?
|
|
Go to Step 12.
|
|
|
|
Replace the camshaft sensing cylinder.
|
|
|
|
STEP 12. M.U.T.-III diagnosis code
|
|
- Reconfirmation of diagnosis code.
|
|
Q.
Is the diagnosis code stored?
|
|
Replace the camshaft position sensor.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|