Code No. P0157: Left Bank Oxygen Sensor (rear) Circuit Low Voltage
OPERATION
- The sensor signal is inputted to the engine-ECU connector terminal O2RL from the left bank oxygen sensor (rear) output terminal.
- The left bank oxygen sensor (rear) is earthed with engine-ECU connector terminal ORLE.
- The engine-ECU connector terminal ORLE applies an offset voltage of 0.5 V to the left bank oxygen sensor (rear) connector terminal.
FUNCTION
- The left bank oxygen sensor (rear) converts the concentration of oxygen in the exhaust emission into a voltage and inputs the signal to the engine-ECU.
- When the air-fuel ratio is richer than the theoretical air-fuel ratio, the left bank oxygen sensor (rear) outputs a voltage of about 1 V. When it is leaner than the theoretical air-fuel ratio, it outputs a voltage of about 0 V.
- In response to the signal, the engine-ECU controls the fuel injection amount so that the air-fuel ratio can be equivalent to the theoretical air-fuel ratio.
TROUBLE JUDGEMENT
Check Conditions
- Left bank oxygen sensor (rear) offset voltage is more than 0.4 V and is less than 0.6 V.
- Battery positive voltage is more than 11 V and is less than 16.5 V.
- More than 3 minutes have passed since the engine starting sequence was completed.
Judgement Criterion
- Left bank oxygen sensor (rear) output voltage is less than 0.2 V for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
PROBABLE CAUSES
- Failed left bank oxygen sensor (rear)
- Open/short circuit or harness damage in left bank oxygen sensor (rear) circuit or loose connector contact
- Failed engine-ECU
|
STEP 1. M.U.T.-III data list
|
|
- Data list reference table (Refer to ).
- Item AF: Left bank oxygen sensor (rear)
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Voltage measurement at left bank oxygen sensor (rear) connector (ORLE line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(3)Check the voltage between the left bank oxygen sensor (rear) connector (ORLE line) and body earth. OK: 0.4 - 0.6 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check of short to earth and open circuit in ORLE line between left bank oxygen sensor (rear) connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 4. M.U.T.-III data list
|
|
- Data list reference table (Refer to ).
- Item AF: Left bank oxygen sensor (rear)
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
Replace the engine-ECU.
|
|
|
|
STEP 5. Check of harness damage in ORLE line between left bank oxygen sensor (rear) connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 6. Voltage measurement at left bank oxygen sensor (rear) connector (O2RL line).
|
|
(1)Use special tool test harness (MB991316) to connect connector, and measure at pick-up harness.
|
|
(2)Transmission: 2nd speed
|
|
(3)Drive with wide open throttle
|
|
(4)Engine: 3,500 r/min or more
|
|
(5)Check the voltage between the left bank oxygen sensor (rear) connector (O2RL line) and body earth. OK:
The output voltage should be 1.1 - 1.5 V.
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Check left bank oxygen sensor (rear) itself.
|
|
- Left bank oxygen sensor (rear) check (Refer to ).
|
|
Q.
Is the check result normal?
|
|
Repair or replace the connector(s), or check and repair the harness of short circuit to earth in O2RL line between left bank oxygen sensor (rear) connector and engine-ECU connector.
|
|
|
|
Replace the left bank oxygen sensor (rear).
|
|
|
|
STEP 8. Check of open circuit and damage in O2RL line between left bank oxygen sensor (rear) connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|