Inspection Procedure
4: Cruise Control cannot be Set (No Response SET - Switch and RES + Switch is
Pressed).
COMMENTS ON TROUBLE SYMPTOM
The fail-safe function is probably cancelling cruise control system. In this case, checking
the cruise control system, MPI system, CAN bus system and CVT system diagnosis codes. The M.U.T.-III
can also be used to check if the circuits of each input switches are normal or not by checking
the data list.
note |
Press the cruise control switches one by one securely. Otherwise, the cruise control system
may not be started.
|
PROBABLE CAUSES
- Malfunction of CAN bus system.
- Malfunction of the MPI system.
- Malfunction of the CVT system.
- Malfunction of the A/T system.
- Malfunction of the cruise control switches.
- Malfunction of the stop lamp switch.
- Malfunction of the inhibitor switch.
- Malfunction of the engine-ECU.
|
caution |
- If there is any problem in the CAN bus lines,
an incorrect diagnosis code may be stored. Prior to this diagnosis, diagnose the CAN bus lines.
- Before replacing the ECU, ensure that the CAN bus lines is normal.
|
|
|
STEP 1. Check the CAN bus system diagnosis.
|
|
Using M.U.T.-III, perform CAN bus diagnosis (Refer to GROUP 54C - Explanation
About The M.U.T-III Can Bus Diagnostics ).
|
|
Q.
Is the check result satisfactory?
|
|
Go to Step 2.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - Troubleshooting, Can Bus
Diagnostic Table ). Then go to Step 9.
|
|
|
|
STEP 2. Check the MPI system diagnosis code.
|
|
Using M.U.T.-III, perform MPI system diagnosis code (Refer to GROUP 13A - Troubleshooting,
Diagnosis Function <4B1>, GROUP 13B - Troubleshooting,
Diagnosis Function <6B3>).
|
|
Q.
Is any diagnosis code stored?
|
|
Repair the MPI system (Refer to GROUP 13A - Troubleshooting, Inspection
Chart for Diagnosis Code <4B1>, GROUP 13B - Troubleshooting, Inspection
Chart for Diagnosis Code <6B3>). Then go to Step 9.
|
|
|
|
Go to Step 3
|
|
|
|
STEP 3. Check the transmission system diagnosis code.
|
|
Using M.U.T.-III, perform transmission system diagnosis code (Refer to GROUP 23A - Troubleshooting,
Diagnosis Function <CVT>, Refer to GROUP 23C - Troubleshooting, Diagnosis
Function <A/T>).
|
|
Q.
Is any diagnosis code stored?
|
|
Repair the transmission system (Refer to GROUP 23A - Troubleshooting,
Inspection Chart for Diagnosis Code <CVT>, GROUP 23C - Troubleshooting,
Inspection Chart for Diagnosis Code <A/T>). Then go to Step
9.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Read the diagnosis code.
|
|
(1)Use the M.U.T.-III, erase the diagnosis code of the cruise control system.
|
|
(2)Turn the ignition switch to the "ON" position, and press the cruise control ON/OFF
switch to turn the cruise control system to ON (turn ON the cruise control indicator lamp).
|
|
(3)After turning the cruise control system to ON, when 2 minutes or more has elapsed
without operating the cruise control switches.
|
|
(4)With the cruise control switches not operated, depress the brake pedal for several
seconds, and then read the diagnosis code of the cruise control system (Refer to .)
|
|
Q.
Is any diagnosis code stored?
|
|
Repair the cruise control system (Refer to - Diagnosis
Code Chart). Then go to Step 9.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Check the data list.
|
|
Using M.U.T.-III, check the data list (Refer to data list reference table ).
|
|
- Item 75: CANCEL switch
- Item 86: Cruise control ON/OFF switch
- Item 91: RES + switch
- Item 92: SET - switch
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Check the cruise control switch system (Refer to - Diagnosis
Code Procedures, Code No. P0578: Abnormal voltage at cruise control switch). Then go to Step
9.
|
|
|
|
STEP 6. Check the data list.
|
|
Using M.U.T.-III, check the data list (Refer to data list reference table ).
|
|
- Item 74: Stop lamp switch
- Item 89: Brake switch
|
|
Q.
Is the check result normal?
|
|
Go to Step 7
|
|
|
|
Check the stop lamp switch system (Refer to - Diagnosis
Code Procedures, Code No. P0504: Malfunction of the stop lamp switch system). Then go to Step
9.
|
|
|
|
STEP 7. Check the data list.
|
|
Using M.U.T.-III, check the data list (Refer to data list reference table ).
|
|
- Item 88: Inhibitor switch
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Check the CVT system (Refer to GROUP 23A - Troubleshooting, Inspection
Procedures for Diagnosis Code, Code No.P0705: Malfunction of Inhibitor Switch <4B1>,
Refer to GROUP 23C - Troubleshooting, Inspection Procedures for Diagnosis Code, Code
No.P0705: Malfunction of Inhibitor Switch <6B3>) . Then
go to Step 9.
|
|
|
|
STEP 8. Check the symptom.
|
|
Q.
Can cruise control be set?
|
|
It can be assumed that this malfunction is intermittent (Refer to GROUP 00 - How
to Use Troubleshooting/Inspection Service Points, How to Cope with Intermittent Malfunction ).
|
|
|
|
Replace the engine-ECU (Refer to GROUP 13A - Engine-ECU <4B1>,
GROUP 13B - Engine-ECU <6B3>). Then go to Step
9.
|
|
|
|
STEP 9. Check the symptom.
|
|
Q.
Can cruise control be set?
|
|
The procedure is complete.
|
|
|
|
Return to Step 1.
|
|
|