INSPECTION PROCEDURE
2: Shifting the S-AWC Drive Mode-selector Does not Change the Mode.
COMMENTS ON TROUBLE SYMPTOM
- If the drive mode cannot be switched by pushing the S-AWC drive mode-selector,
the S-AWC drive mode-selector, the wiring harness wires between the AWC-ECU and the S-AWC drive
mode-selector, the wiring harness wire in the earth circuit for the S-AWC drive mode-selector,
the AWC-ECU or the combination meter may have a problem.
PROBABLE CAUSES
- Damaged wiring harness and connectors
- Malfunction of S-AWC drive mode-selector
- AWC-ECU malfunction
- Malfunction of combination meter
|
|
STEP 1. M.U.T.-III data list.
|
|
|
Check the following data list. (Refer to  ).
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 4.
|
|
|
|
|
|
 Go to Step 2.
|
|
|
|
|
|
STEP 2. Follow combination meter trouble symptom procedure 9 "The
combination meter lamp does not illuminate normally or the multi-information display is not displayed
normally."
|
|
|
Refer to GROUP 54A - Combination Meter.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 4.
|
|
|
|
|
|
Repair it. Then go to Step 3.
|
|
|
|
|
|
STEP 3. Retest the system.
|
|
|
Q.
Does the malfunction occur again?
|
|
|
Go to Step 4.
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|
|
|
STEP 4. Resistance measurement between the S-AWC drive mode-selector
connector terminals
|
|
|
(1)Remove the S-AWC drive mode-selector (Refer to GROUP 52B - Front floor
console).
|
|
|
(2)Measure the resistance between the terminals (Refer to ).
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 5.
|
|
|
|
|
|
Replace the S-AWC drive mode-selector (Refer to GROUP 52B - Front floor
console). Then go to Step 7.
|
|
|
|
|
|
STEP 5. Wiring harness check
|
|
|
(1)Check the wiring harness between the AWC-ECU connector (terminal SW-1) and the
S-AWC drive mode-selector connector.
|
|
|
(2)Check the connector(s) or terminal(s) or wiring harness above for damage or other
problem.
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 6.
|
|
|
|
|
|
Repair the connector(s) or terminal(s) or wiring harness.Then go to Step 7.
|
|
|
|
|
|
STEP 6. Resistance measurement at the S-AWC drive mode-selector connector
|
|
|
(1)Disconnect the S-AWC drive mode-selector connector.
|
|
|
(2)Measure the resistance between the S-AWC drive mode-selector wiring harness side
connector and the body earth.
OK: Continuity exists (2 Ω or less)
|
|
|
Q.
Is the check result normal?
|
|
|
Go to Step 7.
|
|
|
|
|
|
Repair the connector(s) or terminal(s) or wiring harness.Then go to Step 7.
|
|
|
|
|
|
STEP 7. Retest the system.
|
|
|
Q.
Does the malfunction occur again?
|
|
|
Replace the AWC-ECU. (Refer to .)
|
|
|
|
|
|
This diagnosis is complete.
|
|
|
|