Code No. C2104 Valve
power supply circuit
|
caution |
If there is any problem in
the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose
the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
|
|
|
- ABS-ECU contains the power supply circuit (+BV terminal) for the
solenoid valve. The solenoid valve is energised by the valve relay, which is incorporated in
ABS-ECU.
- The valve relay, which is incorporated in ABS-ECU, is always energising the solenoid
valve unless the initial check is in progress when the ignition switch is turned on, and the recurrent
system check is in progress.
|
|
DIAGNOSIS CODE SET CONDITIONS
|
|
This diagnosis code will be set when the solenoid valve supply voltage is not within the
standard value.
|
|
Current trouble
- Fusible link malfunction
- Damaged wiring harness and connectors
- Abnormality in battery or alternator
- ABS-ECU malfunction
|
|
Past trouble
- Carry out diagnosis with particular emphasis on wiring harness and
connector failures between the power supply circuit (+BV terminal) to ABS-ECU solenoid
valve or earth circuit (GND1, GND2 terminal). For diagnosis procedures, refer to How to treat
past trouble (GROUP 00 - How to Use Troubleshooting/How to Treat Past Trouble
).
|
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
Q.
Is the diagnosis code No.C2104 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
Refer to GROUP 54A - Battery Test .
|
|
Q.
Is the battery in good condition?
|
|
Go to Step 4.
|
|
|
|
Replace the battery. Then go to Step 10.
|
|
|
|
STEP 4. Charging system check
|
|
Refer to GROUP 16 - On-vehicle Service/Alternator Output Line
Voltage Drop Test .
|
|
Q.
Is the charging system in good condition?
|
|
Go to Step 5.
|
|
|
|
Repair or replace the charging system component(s). Then go to Step 10.
|
|
|
|
STEP 5. Fusible link check: Check the fusible link No.4 and SBF7.
|
|
Visually check for open circuit in the fusible link No.4 and SBF7.
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 6. Resistance measurement at ABS-ECU connector
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Disconnect the fusible link No.SBF7.
|
|
(3)Resistance between the +BV terminal and the body earth. OK: No continuity
|
|
Q.
Is the check result normal?
|
|
Replace the fusible link No.4 or SBF7. Then go to Step 10.
|
|
|
|
The short circuit may be present in the power supply circuit. Repair the wiring
harness between the ABS-ECU connector +BV terminal and the fusible link, and then replace
the fusible link No.4 or SBF7. Then go to Step 10.
|
|
|
|
STEP 7. Voltage measurement at the ABS-ECU connector
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Measure the voltage between the +BV terminal and the body earth. OK: Approximately system voltage
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
The open circuit may be present in the power supply circuit. Repair the wiring
harness between the ABS-ECU connector +BV terminal and the fusible link. Then go to
Step 10.
|
|
|
|
STEP 8. Resistance measurement at ABS-ECU connector
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Resistance between the GND1 terminal and the body earth, and between the GND2 terminal
and the body earth OK: Continuity exists (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
An open circuit may be present in the earth circuit. Repair the wiring harness
between the ABS-ECU connector GND1 terminal and the body earth, and between the ASC-ECU connector
GND2 terminal and the body earth. Then go to Step 10.
|
|
|
|
STEP 9. Check whether the diagnosis code is reset.
|
|
Erase the diagnosis code.
|
|
Q.
Is the diagnosis code No.C2104 set?
|
|
Replace the hydraulic unit (integrated with ABS-ECU) (Refer to ). Then
go to Step 10.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/ How
to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 10. Check whether the diagnosis code is reset.
|
|
Erase the diagnosis code.
|
|
Q.
Is the diagnosis code No.C2104 set?
|
|
Return to Step 1.
|
|
|
|
This diagnosis is complete.
|
|
|