Code No. U1195
Coding not completed
Code No. U1197 Coding data unavailable
|
caution |
- If there is
any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table
).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
- When the diagnosis code U1195 or U1197 is set in ABS-ECU, the diagnosis code may
also be set in ETACS-ECU. When the diagnosis code is set in ETACS-ECU, carry out the diagnosis
of the diagnosis code for ETACS-ECU first.
|
|
|
ABS-ECU receives the vehicle information stored in the ETACS-ECU via CAN bus lines.
|
|
DIAGNOSIS CODE SET CONDITIONS
|
|
ABS-ECU communicates with ETACS-ECU via CAN bus lines.
|
|
This diagnosis code No.U1195 is set when the variant coding for ETACS-ECU has not been
implemented.
|
|
This diagnosis code No.U1197 is set when there is difference between the vehicle information
from the ETACS-ECU and the vehicle information stored in the ABS-ECU.
|
|
Code No.C1195 is set
- Variant coding for ETACS-ECU has not been implemented.
- ABS-ECU malfunction
|
|
Code No.C1197 is set
- Malfunction of ETACS-ECU
- ETACS-ECU have been interchanged between two vehicles.
- ABS-ECU malfunction
- External noise interference
- ABS-ECU have been interchanged between two vehicles.
|
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
Q.
Is the diagnosis code No. U1195 or U1197 set?
|
|
Go to Step 3.
|
|
|
|
The procedure is complete.
|
|
|
|
STEP 3. M.U.T.-III other system diagnosis code
|
|
Use M.U.T.-III to check whether the ETACS-ECU-related diagnosis code is set or not.
|
|
Q.
Is any diagnosis code set?
|
|
Troubleshoot for the relevant diagnosis code.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check ETACS coding data
|
|
Refer to GROUP 00 - Coding List .
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. ETACS-ECU variant coding
|
|
Perform the variant coding to the ETACS-ECU.
|
|
Q.
Dose variant coding succeed?
|
|
Go to Step 7.
|
|
|
|
Replace the ETACS-ECU (Refer to GROUP 54A - ETACS-ECU ), and
then go to Step 7.
|
|
|
|
STEP 6. Check part number of ABS-ECU
|
|
Check the part number of ABS-ECU.
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Replace the hydraulic unit (integrated with ABS-ECU) (Refer to ). Then
go to Step 8.
|
|
|
|
STEP 7. Check whether the diagnosis code is reset.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch to the "OFF" position.
|
|
(3)Turn the ignition switch to the "ON" position.
|
|
(4)Turn the ignition switch to the "OFF" position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check that the ABS warning lamp goes out.
|
|
Q.
Is the diagnosis code No.U1195 or U1197 set?
|
|
Replace the hydraulic unit (ABS-ECU) (Refer to ). Then
go to Step 8.
|
|
|
|
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to Use Troubleshooting/How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 8. Check whether the diagnosis code is reset.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch to the "OFF" position.
|
|
(3)Turn the ignition switch to the "ON" position.
|
|
(4)Turn the ignition switch to the "OFF" position.
|
|
(5)Turn the ignition switch to the "ON" position.
|
|
(6)Check that the ABS warning lamp goes out.
|
|
Q.
Is the diagnosis code No.U1195 or U1197 set?
|
|
Return to Step 1.
|
|
|
|
This diagnosis is complete.
|
|
|