Code No.C1521
Motor turning angle (output)
Code No.C1522 Motor turning angle range
|
caution |
- If there is
any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis,
diagnose the CAN bus lines (Refer to GROUP 54C, CAN Bus Diagnostics Table).
- Whenever ECU is replaced, ensure that the CAN bus lines are normal.
|
|
|
Power is supplied to the resolver from the EPS-ECU.
|
|
To output the voltage based on the motor rotation angle to the EPS-ECU, the voltage is
supplied to the resolver.
|
|
Check Conditions
The power supply circuit system diagnosis code (No. C1540, C1541) is not set.
|
|
Judgement Criterion
The resolver input voltage or the resolver output voltage does not meet a predetermined
voltage stored in the microcomputer, and the microcomputer determines that there is a problem
in the resolver system.
|
|
Fail Safe, Back Up Function
The EPS-ECU stops the motor control and illuminates the electric power steering
warning display, then sets the diagnosis code No. C1521 and C1522.
|
|
- Malfunction of CAN bus line
- Defective resolver of the steering column shaft assembly
- Defective harness wire(s) or connector(s)
- Short or open circuit between the EPS-ECU and the resolver or loose connector
contact
- Malfunction of the EPS-ECU
|
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ).
On completion, go to Step 2.
|
|
|
|
STEP 2. Diagnosis code recheck after resetting CAN bus lines
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis codes C1521 or C1522 set?
|
|
Go to Step 3.
|
|
|
|
This diagnosis is complete.
|
|
|
|
STEP 3. Check of short to power supply, short to earth, and open circuit
in S1+, S3-, S2+, S4-, R1+, R2- line between
EPS-ECU connector and resolver
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 4. M.U.T.-III data list
|
|
Check the following data list .
|
|
- Item No. 04: Motor current
- Item No. 05: Motor current (target)
- Item No. 17: Motor electric angle
- Item No. 18: Motor speed
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis codes C1521 or C1522 set?
|
|
Replace the EPS-ECU (Refer to ).Then go to
Step 6.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
STEP 6. Check whether the diagnosis code is reset.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis codes C1521 or C1522 set?
|
|
Replace the steering column shaft assembly (Refer to ).Then
go to Step 7.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunctions ).
|
|
|
|
STEP 7. Check whether the diagnosis code is reset.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis codes C1521 or C1522 set?
|
|
Return to Step 1.
|
|
|
|
This diagnosis is complete.
|
|
|