Code No. U0100 Engine CAN timeout
Code No. U0114 4WD CAN timeout


caution
  • If there is any problem in the CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the CAN bus lines (Refer to GROUP 54C, CAN Bus Diagnostics Table ).
  • Whenever ECU is replaced, ensure that the CAN bus lines are normal.

OPERATION

    The signals from the engine-ECU and 4WD-ECU or AWC-ECU are sent to the EPS-ECU.

FUNCTION

    The signals from the engine-ECU and 4WD-ECU or AWC-ECU are sent to the EPS-ECU for motor control.

TROUBLE JUDGEMENT
Check Conditions
  • The power supply circuit system diagnosis code (No. C1540, C1541) is not set.
  • The diagnosis code related to engine circuit system and 4WD circuit system or S-AWC circuit system is set.
Judgement Criterion
    The signals from the engine-ECU and 4WD-ECU or AWC-ECU are not sent, and the microcomputer determines that there is a problem in the system.
Fail Safe, Back Up Function
  • The EPS-ECU sets diagnosis code No. U0100 or U0114. If diagnosis code No. U0100 or U0114 is set, the ECU displays the electric power steering warning symbol to limit the power assistance.

PROBABLE CAUSES

  • Malfunction of CAN bus line
  • Malfunction of the EPS-ECU
  • Malfunction of the engine-ECU
  • Malfunction of the 4WD-ECU <Vehicles without S-AWC>
  • Malfunction of the AWC-ECU <Vehicles with S-AWC>

DIAGNOSIS PROCEDURE

STEP 1. M.U.T.-III CAN bus diagnostics
Use M.U.T.-III to diagnose the CAN bus lines.

Q. Is the check result normal?
Go to Step 3.
Repair the CAN bus lines (Refer to GROUP 54C - CAN Bus Diagnostics Table ). On completion, go to Step 2.

STEP 2. Diagnosis code recheck after resetting CAN bus lines
(1)Erase the diagnosis code.
(2)Turn the ignition switch from the "LOCK" (OFF) position to the "ON" position.
(3)Check if the diagnosis code is set.

Q. Is diagnosis code U0100 or U0114 set?
Go to Step 3.
This diagnosis is complete.

STEP 3. M.U.T.-III diagnosis code
Use M.U.T.-III to check if the same diagnosis code (time-out) is set in the other ECU.

  • Engine-ECU (Refer to GROUP 13A - Diagnosis code chart <4B1>, Refer to GROUP 13B - Diagnosis code chart <6B3> or Refer to GROUP 13D - Diagnosis code chart <4N1>).
  • 4WD-ECU (Refer to GROUP 27C - Diagnosis code chart) <Vehicles without S-AWC>.
  • AWC-ECU (Refer to GROUP 23C - Diagnosis code chart ) <Vehicles with S-AWC>.

Q. Is any diagnosis code set?
YES (Code No. U0100 is set) : Replace the engine ECU (Refer to GROUP 13A - Engine-ECU <4B1>, GROUP 13B - Engine-ECU <6B3> or GROUP 13D - Engine-ECU <4N1> ), and then go to Step 4.
YES (Code No. U0114 is set) : Replace the 4WD-ECU (Refer to GROUP 27C - 4WD-ECU) <Vehicles without S-AWC> or AWC-ECU (Refer to GROUP 23C - AWC-ECU ) <Vehicles with S-AWC>, and then go to Step 4.
NO (No diagnosis code is set.) : Go to Step 4.

STEP 4. Check whether the diagnosis code is set again.
(1)Erase the diagnosis code.
(2)Turn the ignition switch from the LOCK (OFF) position to the ON position.
(3)Check if the diagnosis code is set.

Q. Is diagnosis code U0100 or U0114 set?
Replace the EPS-ECU (Refer to ). Then go to Step 5.
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent Malfunction).

STEP 5. Check whether the diagnosis code is set again.
(1)Erase the diagnosis code.
(2)Turn the ignition switch from the LOCK (OFF) position to the ON position.
(3)Check if the diagnosis code is set.

Q. Is diagnosis code U0100 or U0114 set?
Return to Step 1.
This diagnosis is complete.