|
When discarding the seat belt with
pre-tensioner or a vehicle which is equipped with seat
belts with pre-tensioner, be sure to deploy the
pre-tensioner in advance as specified in the
service procedure that follows.
|
|
1.Move the vehicle to flat
and isolated spot.
|
|
2.
caution |
Before starting the work, wait
for 60 seconds or more
after the disconnection of the battery cable.
(Refer to the item 5
of
Service Precautions).
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove
the battery from the vehicle.
|
|
3.Remove the centre pillar
trim lower (Refer to GROUP 52A - Interior Trim ).
|
|
4.Use the flat-tipped
screwdriver to pull out the locking button of floor harness
connector.
After releasing the lock, disconnect the
connector.
note |
When the floor harness
connector is disconnected from the seat belt
pre-tensioner, the
two pins of the seat belt pre-tensioner
connector are automatically shorted. This
prevents the
unintentional deployment of the seat belt
pre-tensioner caused by the static or
others.
|
|
|
5.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special
tool adapter harness (MB991885), and cover the connection
areas with insulation tape. Keep the
other ends of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional deployment of seat belt
pre-tensioner caused by the static
or others.
|
|
|
6.Connect the adapter
harness (MB991885) to the 2-pin connector of seat belt
pre-tensioner,
and then pull out the deployment wire to outside the
vehicle. 7.In order to suppress the operation
sound as much as possible, fully close all the
door windows and close the doors. 8.
caution |
- Make sure that no one
is present inside or near the vehicle
before the deployment.
- Immediately after the pre-tensioner
deployment, the inflator is extremely
hot. Thus,
before handling, leave the inflator for
30 minutes or more to cool.
- If the seat belt pre-tensioner does not
deploy, consult with your
distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the vehicle.
Then, connect the wires to the removed vehicle battery to
deploy the seat belt pre-tensioner. 9.Discard the
deployed seat belt pre-tensioner according to the disposal
procedures
(Refer to ).
|
|
1.
caution |
Before starting the work, wait
for 60 seconds or more
after the disconnection of the battery cable.
(Refer to the item 5
of
Service Precautions).
|
Disconnect the (-) and (+) terminals of
battery cable, and then remove
the battery from the vehicle.
|
|
2.
caution |
When the connector is
disconnected, the two pins of seat belt
pre-tensioner are automatically shorted to
prevent the unintentional deployment caused by
the
static or others.
|
Remove the seat belt with pre-tensioner from the
vehicle (Refer to ).
|
|
3.Connect the deployment
wires of 6 m or more to each of the two wiring harnesses of
special
tool adapter harness (MB991885), and cover the connection
areas with insulation tape. Keep the
other ends of deployment wires connected to each other
(shorted).
note |
This prevents the
unintentional deployment of seat belt
pre-tensioner by the static or
others.
|
4.Pass a thick wire through the seat belt
pre-tensioner bracket hole, and attach it
to the old tyre with wheel. 5.Connect the adapter
harness to the seat belt pre-tensioner
connector. 6.
caution |
Set so that the connector of
pre-tensioner adapter harness does
not get pinched between the tyres when
deployed.
|
Pull out the seat belt to outside the tyre.
|
|
7.Place an old tyre without
wheel onto the seat belt with pre-tensioner.
|
|
8.
caution |
- Make sure that no one is present near
the seat belt with pre-tensioner
before the deployment.
- Immediately after the seat belt
pre-tensioner deployment, the inflator
is extremely
hot. Thus, before handling, leave the
inflator for 30 minutes or more to
cool.
- If the seat belt pre-tensioner does not
deploy, consult with your
distributor.
|
Disconnect the deployment wire connection at a place
as far as possible from the seat
belt with pre-tensioner. Then, connect the wires to the
removed vehicle battery to deploy the
seat belt pre-tensioner. 9.Discard the deployed
seat belt with pre-tensioner according to the disposal
procedures
(Refer to ).
|
|
After deployment and operation, the
air bag module and seat belt pre-tensioner should
be disposed of in the same manner as any other scrap parts,
adhering to local laws and/or legislation.
Observe the following precautions during air bag or seat
belt pre-tensioner disposal:
|
|
1.Immediately after the
pre-tensioner deployment, the inflator is extremely hot.
Thus,
before handling, leave the inflator for 30 minutes or more
to cool.
|
|
2.Do not pour water or oil
onto the deployed pre-tensioner.
|
|
3.To the deployed
pre-tensioner, substances that irritate eyes and skin may be
deposited.
Therefore, wear gloves and protective glasses when handling.
When the substance comes in contact
with eyes or skin, flush with a large amount of
water.
|
|
4.Place the seat belt with
pre-tensioner in the sturdy plastic bag, and seal the bag
for disposal.
|
|
5.After the work, be sure to
wash your hands with water.
|