Code No. U1190:
No receive fault detect signal
caution |
- If the diagnosis
code No. U1190 is set, diagnose the CAN bus lines.
- When replacing the ECU, always check that the SRS circuit is normal.
|
TROUBLE JUDGEMENT
ETACS-ECU sends the diagnosis code (U code) detection permission or prohibition signal
to each ECU connected to the CAN-C-Mid bus line. If the SRS-ECU cannot receive the diagnosis
code (U code) detection permission or prohibition signal for 5 seconds after turning the ignition
switch to the ON position, diagnosis code U1190 will be set.
PROBABLE CAUSES
- Malfunction of CAN bus line
- Malfunction of SRS-ECU
- Malfunction of the ETACS-ECU
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2
|
|
|
|
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
|
|
|
|
STEP 2. M.U.T.-III other system diagnosis code
|
|
Check again if the diagnosis code is set to the ETACS-ECU.
|
|
Q.
Is the diagnosis code set?
|
|
Diagnose the ETACS-ECU (Refer to GROUP 54A, Troubleshooting ).
|
|
|
|
Go to Step 3
|
|
|
|
STEP 3. Diagnosis code recheck
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the LOCK (OFF) position to the ON position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the ETACS-ECU. After replacing the ECU, carry out the CAN bus diagnostics.
Then go to Step 4.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction in the CAN bus
line between the ETACS-ECU and the SRS-ECU. (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction .)
|
|
|
|
STEP 4. Diagnosis code recheck
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from the LOCK (OFF) position to the ON position.
|
|
(3)Check if the diagnosis code is set.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the SRS-ECU. After replacing the ECU, carry out the CAN bus diagnostics.
Then go to Step 5.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction in the CAN bus
line between the SRS-ECU and the ETACS-ECU. (Refer to GROUP 00 - How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunction .)
|
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
Recheck if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is reset.
|
|
Q.
Is the diagnosis code set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|