Code No. U0100
Engine CAN timeout
caution |
- If diagnosis
code No.U0100 is set in the SRS-ECU, diagnose the CAN main bus line.
- Whenever the ECU is replaced, ensure that the input and output signal circuits are normal.
|
TROUBLE JUDGEMENT
If signal from the engine-ECU cannot be received for 500 milliseconds or more, the SRS-ECU sets
diagnosis code No. U0100.
PROBABLE CAUSES
- Malfunction of the engine-ECU
- Malfunction of the SRS-ECU
- Malfunction of the CAN bus
|
STEP 1. M.U.T.-III CAN bus diagnostics
|
|
Use the M.U.T.-III to diagnose the CAN bus lines.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2
|
|
|
|
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting ).
On completion, go to Step 6.
|
|
|
|
STEP 2. Check the M.U.T.-III Diagnosis code for other systems
|
|
Check that the engine-ECU set a diagnosis code.
|
|
Q.
Is the diagnosis code set?
|
|
Troubleshoot the engine (Refer to GROUP 13A - Diagnosis Code Chart <2000,
2400>, GROUP 13B -Troubleshooting <3000>)
|
|
|
|
Go to Step 3
|
|
|
|
STEP 3. Check the M.U.T.-III Diagnosis code for other systems
|
|
Check if the diagnosis code No. U0100 is set to ETACS-ECU.
|
|
Q.
Is the diagnosis code set?
|
|
Go to Step 4
|
|
|
|
Go to Step 5
|
|
|
|
STEP 4. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is reset.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the engine-ECU. After replacing the ECU, carry out the CAN bus diagnostics.
Then go to Step 6.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in
the CAN bus lines between the engine-ECU and the SRS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 5. Check whether the diagnosis code is reset.
|
|
Check again if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is not reset.
|
|
Q.
Is the diagnosis code set?
|
|
Replace the SRS-ECU. After replacing the ECU, carry out the CAN bus diagnostics.
Then go to Step 6.
|
|
|
|
A poor connection, open circuit or other intermittent malfunction is present in
the CAN bus lines between the engine-ECU and the SRS-ECU (Refer to GROUP 00, How to Use Troubleshooting/Inspection
Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 6. Check whether the diagnosis code is reset.
|
|
Recheck if the diagnosis code is set to the SRS-ECU.
|
|
(1)Erase the diagnosis code.
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
(3)On completion, check that the diagnosis code is reset.
|
|
Q.
Is the diagnosis code set?
|
|
Return to Step 1.
|
|
|
|
The procedure is complete.
|
|
|