Inspection Procedure
7: Buzzers do not sound normally.
caution
Before replacing the combination
meter, be sure to check that the power supply circuit, earth circuit, and communication circuit
are normal.
COMMENTS ON TROUBLE SYMPTOM
When the following signals are received via the CAN communication or signal line, the
combination meter sounds the incorporated buzzer according to the each pattern. Seat belt reminder function
Sounding request signal from the ACC/FCM-ECU, engine-ECU
LDW warning buzzer
Sounding request signal from the LDW-ECU
AS&G buzzer
Sounding request signal from the AS&G-ECU
Security alarm buzzer
Ignition switch ON signal
Sounding request signal from the ETACS-ECU
Electric steering wheel lock malfunction warning buzzer (vehicles
with OSS)
Ignition switch signal
LIN bus line (local) for electrical steering lock
Actuator driving permission monitoring signal
OSS-related malfunction warning buzzer (vehicles with OSS)
Ignition switch signal
When the following conditions are met, and 1 second or more has elapsed.
+B1 is detected to be ON and +B2
is detected to be OFF.
When +B1 is OFF and +B2 is ON, OSS-ECU detects that the IOD fuse
is mounted.
Engine switch reminder buzzer (vehicles with OSS)
Engine switch ON signal
Driver’s door switch ON signal
Keyless operation key reminder buzzer (vehicles with KOS)
Ignition switch OFF signal
IG knob push switch ON signal
Driver’s door switch ON signal
Lamp reminder buzzer
Ignition switch OFF signal
Lighting switch ON signal
Driver’s door switch ON signal
Door-ajar warning buzzer
Ignition switch ON signal
Any door switch or tailgate switch ON signal
Vehicles speed signal
Freeze warning buzzer
Ignition switch ON signal
Ambient temperature signal
Multi information display interrupt display buzzer
Display condition signal of information display from each warning (When there is
a fixed buzzer sounding pattern for each warning, that pattern has the priority.)
Meter information switch or rheostat illumination switch <High
contrast meter> operation buzzer
Sounding request signal from the CVT-ECU, A/C-ECU, radio and CD player,
Multivision display
Parking brake reminder buzzer
Follow trouble symptom procedure 11 when the parking brake reminder buzzer does
not sound.Refer to .
Rest reminder buzzer
When the time to take a rest which was set on the multi information display is reached.
Meter LCD interrupt display buzzer
A message interrupts another message shown on the multi-information display.
TPMS setting buzzer
Ignition switch ON signal
Sounding request signal from the KOS or ETACS-ECU
ASC pre high temperature warning buzzer/ASC high
temperature warning buzzer
Sounding request signal from the ASC-ECU
Electric Parking brake warning buzzer
Sounding request signal from the electric parking brake ECU
Ultrasonic misacceleration mitigation system warning buzzer
Sounding request signal from the clearance warning control unit
Brake auto hold warning buzzer
Sounding request signal from the ASC-ECU
Brake auto hold switch cancel buzzer
Sounding request signal from the ASC-ECU
Rear cross traffic alert buzzer <Except vehicles for
Argentina>
Sounding request signal from the BSW-ECU
If the buzzer does not sound normally, the connector(s) and wiring harness in the CAN
bus lines, or the ETACS-ECU or the combination meter may have a problem.
PROBABLE CAUSES
Malfunction of combination meter
Damaged harness wires and connectors
Malfunction of ECUs
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III CAN bus diagnostics
Use the M.U.T.-III to diagnose the CAN bus lines.
Q.
Is the check result normal?
Go to Step 2.
Repair the CAN bus line (Refer to GROUP 54C - Troubleshooting).
STEP 2. M.U.T.-III diagnosis code
Check if diagnosis code is set in the combination meter.
Q.
Is the diagnosis code set?
Refer to diagnosis code chart.
Go to Step 3.
STEP 3. M.U.T.-III other system diagnosis code
Check if diagnosis code is set in the engine-ECU, CVT-ECU, A/T-ECU, ABS-ECU,
ASC-ECU, ACC-ECU, AS&G-ECU, KOS-ECU, OSS-ECU, ETACS-ECU, heater controller assembly
(A/C-ECU), electric parking brake ECU, clearance warning control unit, FCM/LDW/AHB-ECU
and BSW-ECU.
Q.
Is the diagnosis code set to the any of the above?
Set to the engine-ECU. : Troubleshoot the engine.
Set to the CVT-ECU. : Troubleshoot the CVT. Refer to GROUP 23A - Diagnosis code chart.
Set to the A/T-ECU. : Troubleshoot the CVT. Refer to GROUP 23C - Diagnosis code chart.
Set to the ABS-ECU. : Troubleshoot the ABS. Refer to GROUP 35B - Troubleshooting.
Set to the ASC-ECU. : Troubleshoot the ASC. Refer to GROUP 35C - Troubleshooting.
Set to the ACC-ECU. : Troubleshoot the ACC. Refer to GROUP 17 - Troubleshooting.
Set to the AS&G-ECU. : Troubleshoot the AS&G. (Refer to GROUP 17 - Diagnosis Code Chart).
Set to the KOS-ECU. : Troubleshoot the KOS. Refer to GROUP 42B - Troubleshooting.
Set to the OSS-ECU. : Troubleshoot the OSS. Refer to GROUP 42B - Troubleshooting.
Set to the ETACS-ECU. : Troubleshoot the ETACS.
Set to the heater controller assembly (A/C-ECU). : Troubleshoot the A/C. Refer to GROUP 55 - Troubleshooting.
Set to the electric parking brake ECU. : Troubleshoot the Electric parking brake. Refer to GROUP 36 - Troubleshooting.
Set to the clearance warning control unit. : Troubleshoot the ultrasonic misacceleration mitigation system.
Set to the FCM/LDW/AHB-ECU. : Troubleshoot the FCM and automatic high beam system.
Set to the BSW-ECU. : Troubleshoot the BSW/RCTA.
The diagnosis code is not set. : Go to Step 4.
STEP 4. Check by M.U.T.-III "Special Function"
Using M.U.T.-III, select "Test" from the special function of the combination meter. Execute
the following item to check the buzzer.
Item 3: Buzzer(AUTO)
Q.
Is the check result normal?
Go to Step 5.
Replace the combination meter.
STEP 5. Retest the system
Check that the buzzers sound normally.
Q.
Is the check result normal?
The trouble can be an intermittent malfunction (Refer to GROUP 00 - How
to use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunction).