Diagnosis Item 15: Diagnose when the M.U.T.-III cannot receive the data sent by ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC>.
caution |
When servicing a CAN bus line, earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do, a component connected to the CAN bus line may be broken.
|
FUNCTION
The diagnostic result demonstrates that "the M.U.T.-III cannot receive the sent data from the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC>" when the M.U.T.-III checks the periodically sent data from each ECU and cannot receive the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> data only.
TROUBLE JUDGEMENT CONDITIONS
M.U.T.-III judges the trouble when the periodically sent data from ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> cannot be received.
PROBABLE CAUSES
- Damaged harness wires and connectors
- Power supply circuit malfunction of the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC>
- Malfunction of the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC>
|
STEP 1. Connector check: joint connector (CAN1) and ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector
|
|
caution |
The strand end of the twist wire should be within 10 cm from the connector. For details refer to .
|
|
|
When checking the joint connector, ensure that its wiring harness side and its short pins are not damaged.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the defective connector. Replace the joint connector as necessary.
|
|
|
|
STEP 2. Resistance measurement at joint connector (CAN1) and ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer to .
|
|
|
(1)Disconnect joint connector (CAN1) and the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector, and measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the LOCK (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN1) terminal No.9 and ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector terminal No.11 OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN1) terminal No.20 and ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector terminal No.10 OK: Continuity (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Power supply to the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> may be suspected. Diagnose the ABS <vehicles without ASC> Refer to GROUP 35B - Troubleshooting , or ASC <vehicles with ASC> Refer to GROUP 35C - Troubleshooting .
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair the wiring harness between joint connector (CAN1) and the ABS-ECU <vehicles without ASC> or ASC-ECU <vehicles with ASC> connector.
|
|
|