Diagnosis Item
20: Diagnose when the M.U.T.-III cannot receive the data sent by engine-ECU.
caution |
When servicing a CAN bus line,
earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do,
a component connected to the CAN bus line may be broken.
|
FUNCTION
The diagnostic result demonstrates that "the M.U.T.-III cannot receive the sent data from
the engine-ECU" when the M.U.T.-III checks the periodically sent data from each ECU and cannot
receive the engine-ECU data only.
TROUBLE JUDGEMENT CONDITIONS
M.U.T.-III judges the trouble when the periodically sent data from engine-ECU cannot be
received.
PROBABLE CAUSES
- Damaged harness wires and connectors
- Power supply circuit malfunction of the engine-ECU
- Malfunction of the engine-ECU
|
STEP 1. Connector check: joint connector (CAN1) <vehicles
without ACC> or joint connector (CAN2) <vehicles with ACC> and engine-ECU
connector
|
|
caution |
The strand end of the twist wire should be within 10 cm from
the connector. For details refer to .
|
|
|
When checking the joint connector, ensure that its wiring harness side and its short pins
are not damaged.
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Repair the defective connector. Replace the joint connector as necessary.
|
|
|
|
STEP 2. Resistance measurement at joint connector (CAN1) <vehicles
without ACC> or joint connector (CAN2) <vehicles with ACC> and engine-ECU
connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
caution |
The test wiring harness should be used. For details refer
to .
|
|
|
(1)Disconnect the joint connector (CAN1) <vehicles without ACC> or
joint connector (CAN2) <vehicles with ACC> and the engine-ECU connector, and
measure at the wiring harness side.
|
|
(2)Turn the ignition switch to the LOCK (OFF) position.
|
|
(3)
caution |
When measuring the resistance, disconnect the negative battery
terminal. For details refer to .
|
Ensure that the negative battery terminal is disconnected.
|
|
(4)Continuity between joint connector (CAN1) terminal No.10 and engine-ECU connector
terminal No.90 <vehicles without ACC> OK: Continuity (2 Ω or less)
|
|
(5)Continuity between joint connector (CAN1) terminal No.21 and engine-ECU connector
terminal No.91 <vehicles without ACC> OK: Continuity (2 Ω or less)
|
|
(6)Continuity between joint connector (CAN2) terminal No.10 and engine-ECU connector
terminal No.90 <vehicles with ACC> OK: Continuity (2 Ω or less)
|
|
(7)Continuity between joint connector (CAN2) terminal No.21 and engine-ECU connector
terminal No.91 <vehicles with ACC> OK: Continuity (2 Ω or less)
caution |
Strictly observe the specified wiring harness repair procedure.
For details refer to .
|
|
|
Q.
Is the check result normal?
|
|
<All the resistances measure 2 Ω or less> Go to Step 3
.
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair
the wiring harness between joint connector (CAN1) <vehicles without ACC> or
joint connector (CAN2) <vehicles with ACC> and the engine-ECU.
|
|
|
|
STEP 3. Resistance measurement at engine-ECU connector.
|
|
caution |
A digital multimeter should be used. For details refer to .
|
|
|
(1)Remove the engine-ECU, and measure at the equipment side.
|
|
(2)Resistance between engine-ECU connector terminal Nos.90 and 91 OK: 120 ± 20 Ω
caution |
Strictly observe the specified wiring harness repair procedure.
For details refer to .
|
|
|
Q.
Is the check result normal?
|
|
<Within 120 ± 20 Ω> Power supply to the engine-ECU
may be suspected. Diagnose the fuel system. (Refer to GROUP 13A - Diagnosis Code Chart <4B1>,
GROUP 13B - Diagnosis Code Chart <6B3>)
|
|
|
|
<Not within 120 ± 20 Ω> Replace the engine-ECU.
|
|
|