Diagnosis Item 21: Diagnose when the M.U.T.-III cannot receive the data sent by FCM/LDW/AHB-ECU. <Vehicles with FCM>
| caution |
When servicing a CAN bus line, earth yourself by touching a metal object such as an unpainted water pipe. If you fail to do, a component connected to the CAN bus line may be broken.
|
FUNCTION
The diagnostic result demonstrates that "the M.U.T.-III cannot receive the sent data from the FCM/LDW/AHB-ECU" when the M.U.T.-III checks the periodically sent data from each ECU and cannot receive the FCM/LDW/AHB-ECU data only.
TROUBLE JUDGEMENT CONDITIONS
M.U.T.-III judges the trouble when the periodically sent data from FCM/LDW/AHB-ECU cannot be received.
PROBABLE CAUSES
- Damaged harness wires and connectors
- Power supply circuit malfunction of the FCM/LDW/AHB-ECU
- Malfunction of the FCM/LDW/AHB-ECU
|
|
STEP 1. Connector check: joint connector (CAN3) and FCM/LDW/AHB-ECU connector
|
|
|
| caution |
The strand end of the twist wire should be within 10 cm from the connector.
|
|
|
|
When checking the joint connector, ensure that its wiring harness side and its short pins are not damaged.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 2.
|
|
|
|
|
|
 Repair the defective connector. Replace the joint connector as necessary.
|
|
|
|
|
|
STEP 2. Resistance measurement at joint connector (CAN3) and FCM/LDW/AHB-ECU connector.
|
|
|
| caution |
A digital multimeter should be used.
|
|
|
|
| caution |
The test wiring harness should be used.
|
|
|
|
(1)Disconnect joint connector (CAN3) and the FCM/LDW/AHB-ECU connector, and measure at the wiring harness side.
|
|
|
(2)Turn the ignition switch to the LOCK (OFF) position.
|
|
|
(3)
| caution |
When measuring the resistance, disconnect the negative battery terminal.
|
Ensure that the negative battery terminal is disconnected.
|
|
|
(4)Continuity between joint connector (CAN3) terminal No.7 and FCM/LDW/AHB-ECU connector terminal No.2 <LHD>
OK: Continuity (2 Ω or less)
|
|
|
(5)Continuity between joint connector (CAN3) terminal No.18 and FCM/LDW/AHB-ECU connector terminal No.8 <LHD>
OK: Continuity (2 Ω or less)
|
|
|
(6)Continuity between joint connector (CAN3) terminal No.5 and FCM/LDW/AHB-ECU connector terminal No.2 <RHD>
OK: Continuity (2 Ω or less)
|
|
|
(7)Continuity between joint connector (CAN3) terminal No.14 and FCM/LDW/AHB-ECU connector terminal No.8 <RHD>
OK: Continuity (2 Ω or less)
| caution |
Strictly observe the specified wiring harness repair procedure.
|
|
|
|
Q.
Is the check result normal?
|
|
|
<All the resistances measure 2 Ω or less> Go to Step 3.
|
|
|
|
|
|
NO : <Either or all of the resistances measure more than 2 Ω> Repair intermediate connector C-223, or the wiring harness between joint connector (CAN3) and the FCM/LDW/AHB-ECU connector.
|
|
|
|
|
|
STEP 3. Resistance measurement at FCM/LDW/AHB-ECU connector.
|
|
|
| caution |
A digital multimeter should be used.
|
|
|
|
(1)Remove the FCM/LDW/AHB-ECU, and measure at the equipment side.
|
|
|
(2)Resistance between FCM/LDW/AHB-ECU connector terminal Nos.2 and 8
OK: 1 kΩ or more
|
|
|
Q.
Is the check result normal?
|
|
|
Power supply to the FCM/LDW/AHB-ECU may be suspected. Diagnose the FCM. Refer to GROUP 35C - Troubleshooting  .
|
|
|
|
|
|
Replace the FCM/LDW/AHB-ECU.
|
|
|
|