REMOVAL AND INSTALLATION

			Crankshaft front oil seal removal steps
		·	Valve timing belt (Refer to ).
		1.	Crank angle sensor
	>>E<<	2.	Crankshaft camshaft drive sprocket
	>>E<<	3.	Crankshaft angle sensing blade
	>>E<<	4.	Timing belt train spacer
		5.	Crankshaft key
	>>D<<	6.	Crankshaft front oil seal
			Crankshaft rear oil seal removal steps
		·	Transmission assembly (Refer to GROUP 22A - Transmission Assembly ) <M/T>
		·	Transmission assembly (Refer to GROUP 23A - Transmission Assembly ) <A/T>
<<A>>	>>C<<	7.	Flywheel bolt <M/T>
		8.	Flywheel assembly <M/T>
<<A>>	>>C<<	9.	A/T Drive plate bolt <A/T>
	>>B<<	10.	A/T drive plate adapter plate <A/T>
	>>B<<	11.	A/T drive plate <A/T>
	>>B<<	12.	Crankshaft A/T drive plate adapter <A/T>
	>>A<<	13.	Crankshaft rear oil seal

REMOVAL SERVICE POINT

<<A>> FLYWHEEL BOLT <M/T>/A/T DRIVE PLATE BOLT <A/T> REMOVAL

1.Use special tool flywheel stopper (MD998781) to secure the flywheel <M/T> or A/T drive plate <A/T>.
2.Remove the flywheel bolts <M/T> or A/T drive plate bolts <A/T>.

INSTALLATION SERVICE POINTS

>>A<< CRANKSHAFT REAR OIL SEAL INSTALLATION

1.Apply a small amount of engine oil to the entire inner diameter of the crankshaft rear oil seal lip.
2.Use the special tool Crankshaft rear oil seal installer (MD998718) to press-fit the crankshaft rear oil seal.

>>B<< CRANKSHAFT A/T DRIVE PLATE ADAPTER <A/T>/A/T DRIVE PLATE <A/T>/A/T DRIVE PLATE ADAPTER PLATE <A/T> INSTALLATION

Install the crankshaft A/T drive plate adapter and A/T drive plate adapter plate on the A/T drive plate in the direction shown in the illustration.

>>C<< FLYWHEEL BOLT <M/T>/A/T DRIVE PLATE BOLT <A/T> INSTALLATION

1.Use special tool flywheel stopper (MD998781) to secure the flywheel <M/T> or A/T drive plate <A/T> in the same manner as removal.
2.Tighten the flywheel bolts <M/T> or A/T drive plate bolts <A/T> to the specified torque.

Tightening torque:

74 ± 1 N·m <M/T>
74 ± 2 N·m <A/T>

>>D<< CRANKSHAFT FRONT OIL SEAL INSTALLATION

1.Apply a small amount of engine oil to the entire inner diameter of the crankshaft front oil seal lip.
2.Apply a small amount of engine oil to the outer diameter of special tool crankshaft front oil seal installer (guide) (MD998717) and install it to the crankshaft.
3.Use special tool crankshaft front oil seal installer (MD998717) to press-fit the crankshaft front oil seal.

>>E<< TIMING BELT TRAIN SPACER/CRANKSHAFT ANGLE SENSING BLADE/CRANKSHAFT CAMSHAFT DRIVE SPROCKET INSTALLATION

To prevent the crankshaft pulley mounting bolt from being loosened, wipe off the dirt on the crankshaft sprocket and the crankshaft as shown in the figure. Also, wipe off the dirt on the crankshaft spacer, crankshaft sensing blade, crankshaft sprocket, and crankshaft as shown in the figure. Then degrease the areas, and install them.