Code No. 15:
Auto-cruise Control Switch System
OPERATION
This circuit judges the signals of each switch
["ON/OFF" (MAIN), "CANCEL",
"COAST/SET" and "ACC/RES"] of the auto-cruise control
switch. The
engine-ECU <M/T> or engine-A/T-ECU
<A/T> detects
the state of the auto-cruise control switch by sensing the voltages shown
below.
- When all switches are OFF: 4.7 - 5.0 volts
- When the "ON/OFF" (MAIN) switch is ON: 0 - 0.5 volt
- When the "CANCEL" switch is ON: 1.0 - 1.8 volts
- When the "COAST/SET" switch is ON: 2.3 - 3.0 volts
- When the "ACC/RES" switch is ON: 3.5 - 4.2 volts
DIAGNOSIS CODE SET CONDITIONS
If the auto-cruise control switch is
operated, this diagnosis code will be set when the
engine-ECU <M/T> or engine-A/T-ECU
<A/T> terminal
voltage is different from the standard value.
Or, this code is set when the
"COAST/SET" switch or "ACC/RES" switch
is stuck to ON.
PROBABLE CAUSES
- Damaged harness or connector.
- Malfunction of the auto-cruise control switch.
- Malfunction of the clock spring.
- Malfunction of the engine-ECU <M/T>.
- Malfunction of the engine-A/T-ECU <A/T>.
|
STEP 1. M.U.T.-III data list.
|
|
- Item 75: "CANCEL" switch
- Item 86: "ON/OFF" (MAIN) switch
- Item 91: "ACC/RES" switch
- Item 92: "COAST/SET" switch
|
|
(Refer to data list reference table ).
|
|
Q.
Is the check result normal?
|
|
Go to Step 2.
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 2. Read the diagnosis code.
|
|
(1)Disconnect the negative (-) battery terminal, and
erase the diagnosis
code of the auto-cruise control system.
|
|
(2)Connect the negative (-) battery terminal.
|
|
(3)Turn the ignition switch to the "ON" position, and press
the "ON/OFF"
(MAIN) switch to turn the auto-cruise control system to ON.
|
|
(4)After turning the auto-cruise control system to ON, when 2
minutes or more has
elapsed without operating the auto-cruise control switches, read the
diagnosis code of the auto-cruise
control system.
|
|
Q.
Is diagnosis code No. 15 set?
|
|
Replace the engine-ECU
<M/T> or engine-A/T-ECU <A/T>
(Refer
to GROUP 13A - Engine-ECU and Engine-A/T-ECU ) <6G72> or
(Refer to GROUP 13B - Engine-ECU and Engine-A/T-ECU ) <6G75>.
Then go to Step 18.
|
|
|
|
It can
be assumed that this malfunction is intermittent (Refer to GROUP 00 -
How
to Use Troubleshooting/Inspection Service Points, How to Cope with
Intermittent Malfunction ).
|
|
|
|
STEP 3. Measure the voltage at auto-cruise control switch connector
D-301.
|
|
(1)Remove the air bag module (driver’s side)
[Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
|
|
(2)Connect the negative (-) battery terminal.
|
|
(3)Turn the ignition switch to the "ON" position and the
"ON/OFF" (MAIN)
switch to the OFF position.
|
|
(4)Measure the voltage between connector D-301 terminal No. 4
and earth. OK: 4.7 - 5.0 V
|
|
(5)Turn the ignition switch to the "LOCK" (OFF)
position.
|
|
Q.
Is the check result normal?
|
|
Go to Step 10.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Measure the voltage at engine-ECU connector D-246
<M/T> or
engine-A/T-ECU connector D-217
<A/T>.
|
|
(1)Turn the ignition switch to the "ON" position and the
"ON/OFF" (MAIN)
switch to the OFF position.
|
|
(2)Measure the voltage between engine-ECU connector D-246
<M/T> or
engine-A/T-ECU connector D-217 <A/T> terminal No. 94
and
earth. OK: 4.7 - 5.0 V
|
|
(3)Turn the ignition switch to the "LOCK" (OFF)
position.
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 5.
|
|
|
|
STEP 5. Connector check: D-246 engine-ECU connector
<M/T> or
D-217 engine-A/T-ECU connector
<A/T>.
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Repair or replace the faulty
connector, and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 6. Check the harness between engine-ECU connector D-246
<M/T> or
engine-A/T-ECU connector D-217 <A/T> terminal No.
94 and
the auto-cruise control switch connector D-301 terminal No.
4.
|
|
(1)Disconnect engine-ECU connector D-246
<M/T> or engine-A/T-ECU
connector D-217 <A/T> and measure at the harness connector
side.
|
|
(2)Measure the continuity between engine-ECU connector D-246
<M/T> or
engine-A/T-ECU connector D-217 <A/T> terminal No. 94
and
earth.
|
|
(3)Connect engine-ECU connector D-246 <M/T>
or engine-A/T-ECU
connector D-217 <A/T>.
|
|
Q.
Is the measured continuity open circuit?
|
|
Install the air bag module
(driver’s side) [Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
Then return to Step 1.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Connectors check: D-301 auto-cruise control switch connector,
D-302 and D-305 clock spring connectors.
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Repair or replace the faulty
connector, and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 8. Check the clock spring.
|
|
Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s)
and Clock Spring Inspection .
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Replace the clock spring and
install the air bag module (driver’s side) [Refer
to GROUP 52B - Driver’s, Front Passenger’s Air Bag
Module(s) and Clock
Spring ]. Then go to Step
18.
|
|
|
|
STEP 9. Check the harness between engine-ECU connector D-246
<M/T> or
engine-A/T-ECU connector D-217 <A/T> terminal No.
94 and
the auto-cruise control switch connector D-301 terminal No.
4.
|
|
Q.
Is the check result normal?
|
|
It can
be assumed that this malfunction is intermittent (Refer to GROUP 00 -
How
to Use Troubleshooting/Inspection Service Points, How to Cope with
Intermittent Malfunction ).
Install the air bag module (driver’s side) [Refer to GROUP 52B
- Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
|
|
|
|
Repair the damaged harness wire,
and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 10. Measure the voltage at auto-cruise control switch connector
D-301.
|
|
(1)Turn the ignition switch to the "ON" position and the
"ON/OFF" (MAIN)
switch to the ON position.
|
|
(2)Measure the voltage between connector D-301 terminal No. 3
and earth. OK: 0.3 V or less
|
|
(3)Turn the "ON/OFF" (MAIN) switch to the OFF position
and the ignition switch
to the "LOCK" (OFF) position.
|
|
Q.
Is the check result normal?
|
|
Go to Step 16.
|
|
|
|
Go to Step 11.
|
|
|
|
STEP 11. Measure the voltage at engine-ECU connector D-247
<M/T> or
engine-A/T-ECU connector D-218
<A/T>.
|
|
(1)Turn the ignition switch to the "ON" position and the
"ON/OFF" (MAIN)
to the ON position.
|
|
(2)Measure the voltage between engine-ECU connector D-247
<M/T> or
engine-A/T-ECU connector D-218 <A/T> terminal No.
146 and
earth. OK: 0.3 V or less
|
|
(3)Turn the "ON/OFF" (MAIN) switch to the OFF position
and the ignition switch
to the "LOCK" (OFF) position.
|
|
Q.
Is the check result normal?
|
|
Go to Step 13.
|
|
|
|
Go to Step 12.
|
|
|
|
STEP 12. Connector check: D-247 engine-ECU connector
<M/T> or
D-218 engine-A/T-ECU connector
<A/T>.
|
|
Q.
Is the check result normal?
|
|
Install the air bag module
(driver’s side) [Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
Then return to Step 1.
|
|
|
|
Repair or replace the faulty
connector, and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 13. Connectors check: D-246 engine-ECU connector
<M/T> or
D-218 engine-A/T-ECU connector <A/T>, D-301
auto-cruise
control switch connector, D-302 and D-305 clock spring
connectors.
|
|
Q.
Is the check result normal?
|
|
Go to Step 14.
|
|
|
|
Repair or replace the faulty
connector, and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 14. Check the clock spring.
|
|
Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s)
and Clock Spring Inspection .
|
|
Q.
Is the check result normal?
|
|
Go to Step 15.
|
|
|
|
Replace the clock spring and
install the air bag module (driver’s side) [Refer
to GROUP 52B - Driver’s, Front Passenger’s Air Bag
Module(s) and Clock
Spring ]. Then go to Step
18.
|
|
|
|
STEP 15. Check the harness between engine-ECU connector D-247
<M/T> or
engine-A/T-ECU connector D-218 <A/T> terminal No.
146 and
the auto-cruise control switch connector D-301 terminal No.
3.
|
|
Q.
Is the check result normal?
|
|
It can
be assumed that this malfunction is intermittent (Refer to GROUP 00 -
How
to Use Troubleshooting/Inspection Service Points, How to Cope with
Intermittent Malfunction ).
Install the air bag module (driver’s side) [Refer to GROUP 52B
- Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
|
|
|
|
Repair the damaged harness wire,
and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 16. Connector check: D-301 auto-cruise control switch
connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 17.
|
|
|
|
Repair or replace the faulty
connector, and install the air bag module (driver’s
side) [Refer to GROUP 52B - Driver’s, Front
Passenger’s
Air Bag Module(s) and Clock Spring ]. Then go to Step
18 .
|
|
|
|
STEP 17. Check the auto-cruise control switch.
|
|
Refer to .
|
|
Q.
Is the check result normal?
|
|
Install the air bag module
(driver’s side) [Refer to GROUP 52B - Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
Then return to Step 1.
|
|
|
|
Replace the auto-cruise control
switch (Refer to ).
Install the air bag module (driver’s side) [Refer to GROUP 52B
- Driver’s,
Front Passenger’s Air Bag Module(s) and Clock Spring ].
Then go to Step 18.
|
|
|
|
STEP 18. M.U.T.-III data list.
|
|
- Item 75: "CANCEL" switch
- Item 86: "ON/OFF" (MAIN) switch
- Item 91: "ACC/RES" switch
- Item 92: "COAST/SET" switch
|
|
(Refer to data list reference table ).
|
|
Q.
Is the check result normal?
|
|
Go to Step 19.
|
|
|
|
Return to Step 3.
|
|
|
|
STEP 19. Read the diagnosis code.
|
|
(1)Disconnect the negative (-) battery terminal, and
erase the diagnosis
code of the auto-cruise control system.
|
|
(2)Connect the negative (-) battery terminal.
|
|
(3)Turn the ignition switch to the "ON" position, and press
the "ON/OFF"
(MAIN) switch to turn the auto-cruise control system to ON.
|
|
(4)After turning the auto-cruise control system to ON, when 2
minutes or more has
elapsed without operating the auto-cruise control switches, read the
diagnosis code of the auto-cruise
control system.
|
|
Q.
Is diagnosis code No. 15 set?
|
|
Replace the engine-ECU
<M/T> or engine-A/T-ECU <A/T>
(Refer
to GROUP 13A - Engine-ECU and Engine-A/T-ECU ) <6G72> or
(Refer to GROUP 13B - Engine-ECU and Engine-A/T-ECU ) <6G75>.
Then go to Step 18.
|
|
|
|
The
procedure is complete.
|
|
|