Code No.P1764 (P0712): A/T fluid temperature sensor system
A/T FLUID TEMPERATURE SENSOR SYSTEM CIRCUIT
Refer to
.
![](../../../img/23/AC607558AB00ENG.png)
![](../../../img/23/AC607560AE00ENG.png)
![](../../../img/23/AC607563BQ00ENG.png)
![](../../../img/23/AC607569BR00ENG.png)
![](../../../img/23/AC607564AW00ENG.png)
![](../../../img/23/AC607571AW00ENG.png)
OPERATION
Refer to
.
DIAGNOSIS CODE SET CONDITION
If the A/T fluid temperature
sensor output voltage has been approximately 0 V for at least one second
(indicating abnormally high oil temperature), it indicates that the A/T
fluid temperature sensor circuit is shorted and diagnosis code No.1764 (P0712)
is set.
PROBABLE CAUSES
- Malfunction of the A/T fluid temperature sensor
- Damaged harness wires and connectors
- Malfunction of the A/T-ECU <4M4>
- Malfunction of the engine-A/T-ECU <6G7>
|
STEP 1. M.U.T.-III data list
|
|
Item 7: A/T fluid temperature sensor
(Refer to Data List Table ).
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to
GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Connector check: C-06 A/T control solenoid valve
assembly
|
|
Check for the contact with terminals.
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Repair
the defective connector.
|
|
|
|
STEP 3. Measure the voltage at A/T control solenoid valve
assembly connector C-06.
|
|
(1)Disconnect the connector, and measure the voltage between
terminal 1 and earth at the wiring harness side.
|
|
(2)Turn the ignition switch to the ON
position. OK: 4.5 - 4.9 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 4. Measure the resistance at A/T control solenoid valve
assembly connector C-06.
|
|
Disconnect the connector, and measure the
resistance between terminal 1 and 2 at the sensor side.
|
|
OK:
- 16.7 - 20.5 kΩ (at 0°C)
- 7.3 - 8.9 kΩ (at 20°C)
- 3.4 - 4.2 kΩ (at 40°C)
- 1.9 - 2.2 kΩ (at 60°C)
- 1.0 - 1.2 kΩ (at 80°C)
- 0.57 - 0.69 kΩ (at 100°C)
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Replace the A/T fluid
temperature sensor.
|
|
|
|
STEP 5. M.U.T.-III data list
|
|
Item 7: A/T fluid temperature sensor
(Refer to Data List Table ).
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to
GROUP 00 - How to Cope with Intermittent Malfunction ).
|
|
|
|
Replace the A/T-ECU<4M4>
or engine-A/T-ECU<6G7>.
|
|
|
|
STEP 6. Measure the voltage at A/T-ECU connector D-38 <4M4>
or engine-A/T-ECU connector D-217 <6G7>.
|
|
(1)Connect A/T control solenoid valve assembly
connector C-06.
|
|
(2)Turn the ignition switch to the ON position.
|
|
(3)Measure the voltage between A/T-ECU connector D-38
terminal No.44 <4M4> and earth or engine-A/T-ECU connector D-217
terminal No.119 <6G7> and earth. OK:
- 3.8 - 4.0 V (at 20°C)
- 3.2 - 3.4 V (at 40°C)
- 1.7 - 1.9 V (at 80°C)
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Connector check: D-225 intermediate connector, D-38 A/T-ECU
connector <4M4> or D-217 engine-A/T-ECU connector
<6G7>
|
|
Check for the contact with terminals.
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Repair
the defective connector.
|
|
|
|
STEP 8. Check the harness between A/T control solenoid valve
assembly connector C-06 terminal No.1 and A/T-ECU connector D-38 terminal
No.44 <4M4> or engine-A/T-ECU connector D-217 terminal No.119
<6G7>.
|
|
Check the output line for short-circuited or
open circuit.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair
the wiring harness.
|
|
|