Code No.53: Motor relay system (open circuit, short circuit or motor relay
coil failure)
![](../../../img/35/W7B35X019A00ENG.png)
![](../../../img/35/AC608527AC00ENG.png)
![](../../../img/35/AC604451AE00ENG.png)
![](../../../img/35/AC607549AC00ENG.png)
![](../../../img/35/AC607552AB00ENG.png)
![](../../../img/35/AC607562AT00ENG.png)
![](../../../img/35/AC607570AT00ENG.png)
![](../../../img/35/AC607563BL00ENG.png)
![](../../../img/35/AC607569BM00ENG.png)
![](../../../img/35/AC607564BF00ENG.png)
![](../../../img/35/AC607571BF00ENG.png)
![](../../../img/35/AC607567AE00ENG.png)
![](../../../img/35/AC607609AE00ENG.png)
OPERATION
- The motor relay 1 and the motor relay 2 are controlled by the
ABS-ECU.
- If the brake fluid pressure in the hydraulic brake booster (HBB) becomes
low, the ABS-ECU outputs the motor relay actuating signal to the motor relay
1 and the motor relay 2 and then the pump motor operates.
- The ABS-ECU monitors the pump motor (at 49 terminal).
DIAGNOSIS CODE SET CONDITIONS
The diagnosis code is set if the
motor relay circuit is open or short, the ABS-ECU internal circuit malfunction
occurs, or if the master cylinder and hydraulic unit assembly malfunction of
the hydraulic brake booster (HBB) occurs.
PROBABLE CAUSES
- Malfunction of the motor relay 1 or the motor relay 2
- Damaged wiring harness or connector
- Malfunction of the ABS-ECU
- Malfunction of the HBB (Master cylinder and hydraulic unit
assembly)
|
STEP 1. Check the pump motor operation.
|
|
(1)Depress the pedal repeatedly more than 40 times until the
pedal depressing force feels heavy with the ignition switch at the "LOCK"
(OFF) position.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
Q.
Does the pump motor operate?
|
|
Go to Step 23.
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Check the motor relay 1.
|
|
Refer to .
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Replace the motor relay 1. Then
go to Step 26.
|
|
|
|
STEP 3. Check the motor relay 2.
|
|
Refer to .
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Replace the motor relay 2. Then
go to Step 26.
|
|
|
|
STEP 4. Check motor relay 1 connector B-13X, motor relay 2 connector
B-12X, HBB connectors B-107 and B-108 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the faulty connector or
terminal. Then go to Step 26.
|
|
|
|
STEP 5. Check the power supply circuit at motor relay 2 harness
connector B-12X.
|
|
(1)Remove the motor relay 2.
|
|
(2)Measure the voltage between terminal 5 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 6.
|
|
|
|
Go to Step 9.
|
|
|
|
STEP 6. Check the ignition switch (IG2) circuit at motor relay 2
harness connector B-12X.
|
|
(1)Remove the motor relay 2.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal 3 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 7.
|
|
|
|
Go to Step 10.
|
|
|
|
STEP 7. Check the power supply circuit at motor relay 1 harness
connector B-13X.
|
|
(1)Remove the motor relay 1.
|
|
(2)Measure the voltage between terminal 4 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 8.
|
|
|
|
Go to Step 12.
|
|
|
|
STEP 8. Check the ignition switch (IG2) circuit at motor relay 1
harness connector B-13X.
|
|
(1)Remove the motor relay 1.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal 3 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 15.
|
|
|
|
Go to Step 13.
|
|
|
|
STEP 9. Check the harness wires between fusible link number 32 and
motor relay 2 connector B-12X (terminal 2).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 10. Check intermediate connectors D-113 <4M4>, D-111
<6G7>, D-230, D-34, junction block connector D-403 and
junction block connector D-405 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 11.
|
|
|
|
Repair the faulty connector or
terminal. Then go to Step 26.
|
|
|
|
STEP 11. Check the harness wires between motor relay 2 connector B-12X
(terminal 3) and junction block connector D-403 (terminal
2).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 12. Check the harness wires between fusible link number 32 and
motor relay 1 connector B-13X (terminal 4).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 13. Check intermediate connector D-231 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 14.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 14. Check the harness wires between motor relay 1 connector B-13X
(terminal 3) and multi-purpose fuse number 22 (junction
block).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 15. Check the following harness wires.
|
|
- The wire between HBB connector B-108 (terminal 31) and motor relay 2
connector B-12X (terminal 5)
- The wire between HBB connector B-107 (terminal 2) and motor relay 1
connector B-13X (terminal 5)
|
|
Q.
Is the check result normal?
|
|
Go to Step 16.
|
|
|
|
Repair or replace the faulty
harness wire. Then go to Step 26.
|
|
|
|
STEP 16. Check ABS-ECU connector D-251 and D-250 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 17.
|
|
|
|
Repair the faulty connector or
terminal. Then go to Step 26.
|
|
|
|
STEP 17. Check the ignition switch (IG2) circuit at ABS-ECU harness
connector D-250.
|
|
(1)Disconnect ABS-ECU connector D-250.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal 38 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 18.
|
|
|
|
Go to Step 19.
|
|
|
|
STEP 18. Check the ignition switch (IG2) circuit at ABS-ECU harness
connector D-251.
|
|
(1)Disconnect ABS-ECU connector D-251.
|
|
(2)Turn the ignition switch to the "ON" position.
|
|
(3)Measure the voltage between terminal 6 and body
earth. OK: Approx. 12 volts (battery positive
voltage)
|
|
Q.
Is battery positive voltage (approx. 12 volts) present?
|
|
Go to Step 21.
|
|
|
|
Go to Step 20.
|
|
|
|
STEP 19. Check the harness wires between ABS-ECU connector D-250
(terminal 38) and motor relay 2 connector B-12X (terminal
1).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 20. Check the harness wires between ABS-ECU connector D-251
(terminal 6) and motor relay 1 connector B-13X (terminal 1).
|
|
Q.
Is the check result normal?
|
|
Go to Step 26.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 21. Check the HBB (continuity and resistance test of the pump
motor).
|
|
Refer to .
|
|
Q.
Is the check result normal?
|
|
Go to Step 23.
|
|
|
|
Go to Step 22.
|
|
|
|
STEP 22. Check the pump motor and lead wire.
|
|
(1)Remove the HBB (Refer to ).
|
|
(2)Remove the pump motor and the lead wire from the HBB
(Refer to ).
|
|
(3)Check the following items:
- Confirm that the pump motor operates when the battery voltage is
imposed at the pump motor terminal.
- Confirm the continuity of the lead wire.
|
|
Q.
Is the check result normal?
|
|
Replace the master cylinder and
hydraulic unit assembly (Refer to ). Then go to Step 26.
|
|
|
|
Replace the pump motor or the
lead wire (Refer to ). Then go to Step 26.
|
|
|
|
STEP 23. Check HBB connector B-107 and ABS-ECU connector D-250 for
loose, corroded or damaged terminals, or terminals pushed back in the
connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 24.
|
|
|
|
Repair the faulty connector or
terminal. Then go to Step 26.
|
|
|
|
STEP 24. Check the harness wires between ABS-ECU connector D-250
(terminal 49) and HBB connector B-107 (terminal 4).
|
|
Q.
Is the check result normal?
|
|
Go to Step 25.
|
|
|
|
Repair or replace it. Then go to
Step 26.
|
|
|
|
STEP 25. Recheck for diagnosis code.
|
|
(1)Erase the diagnosis code.
|
|
(2)Recheck for diagnosis code.
|
|
Replace the ABS-ECU (Refer to
GROUP 35B, ABS Control Unit ). Then go to Step 26.
|
|
|
|
It can
be assumed that this malfunction is intermittent. Refer to GROUP 00, How to
Use Troubleshooting/Inspection Service Points - How to Cope
with Intermittent Malfunction .
|
|
|
|
STEP 26. Recheck for diagnosis code.
|
|
(1)Erase the diagnosis code.
|
|
(2)Recheck for diagnosis code.
|
|
Start over at Step 1.
|
|
|
|
The
procedure is complete.
|
|
|