INSPECTION PROCEDURE
5: The Sunroof Inhibition Function does not work Normally (The
Sunroof Operation Lock Warning
Buzzer does not Sound). <Vehicles for South
Africa>
caution
Whenever the ECU is replaced, ensure that
the input
and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the sunroof inhibition
function does not work normally, the sunroof motor assembly,
the power window main switch or the ETACS-ECU may be defective.
POSSIBLE CAUSES
Malfunction of the power window main switch
Malfunction of the sunroof motor assembly
Malfunction of the ETACS-ECU
Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
STEP 1. Which does not operate normally, the
sunroof inhibition
or the sunroof operation lock buzzer?
Q.
Which does not operate normally, the sunroof inhibition or the
sunroof operation lock
buzzer?
YES (The sunroof inhibition does not work
normally.) :
Go to Step 2.
YES (The sunroof operation lock buzzer does not
work normally.) : Go to Step
4.
YES (Neither operates normally.) : Go to Step
5.
Go
to Step 10.
STEP 2. Check for sunroof
diagnosis code.
Check whether the sunroof-related diagnosis
code is set.
Q.
Is the diagnosis code set?
Go to Step
3.
Refer to GROUP54B,
Diagnosis Code Chart or
GROUP54C, Diagnosis Code Chart .
STEP 3. Check the operation of the
sunroof.
Check that the sunroof works normally by using the
sunroof switch.
Q.
Is the check result normal?
The trouble can be an
intermittent malfunction (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope with
Intermittent Malfunction ).
Refer to .
STEP 4. Check the power supply
circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning
lamps illuminate.
Q.
Is the check result normal?
Replace the
ETACS-ECU.
Refer to
GROUP 54A, inspection procedure A-1 "Check the battery power supply
circuit to
the ETACS-ECU <Not using SWS
monitor> or <Using
SWS monitor>."
STEP 5. Confirm the
operation of the power windows.
Check that each of the power
windows (excluding the driver’s door) works normally
by using the power window main switch.
Q.
Is the check result normal?
Go to Step
6.
Refer to .
STEP 6. Confirm the operation of the power
windows.
Turn on the power window lock switch. Check that
neither of the power windows (excluding
the driver’s door) works when the relevant power window sub switch
is operated.
Q.
Is the check result normal?
Replace to the power window main
switch.
Go to Step 7.
STEP 7. Check the operation of the
sunroof.
Check that the sunroof works normally by using the
sunroof switch.
Q.
Is the check result normal?
Go to Step
8.
Refer to .
STEP 8. Check the power supply
circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning
lamps illuminate.
Q.
Is the check result normal?
Go to Step
9.
Refer to GROUP 54A,
inspection procedure A-1 "Check the battery power supply circuit to
the ETACS-ECU <Not using SWS
monitor> or <Using
SWS monitor>."
STEP 9. M.U.T.-III
diagnosis code
When the ignition switch is turned to the
LOCK (OFF) position, check that the ETACS-ECU
does not set the diagnosis code.
Q.
Is the diagnosis code set?
Refer to GROUP54B, Diagnosis
Code Chart or
GROUP54C, Diagnosis Code Chart .
The trouble can be an
intermittent malfunction (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope with
Intermittent Malfunction ).
STEP 10. Retest the system.
Check that the
sunroof inhibition function work normally.
Q.
Is the check result normal?
The trouble can be an
intermittent malfunction (Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points - How to Cope with
Intermittent Malfunction ).