|
1.Remove the oil pan
mounting bolts.
|
![](../../../img/11/ACE02393AB00ENG.png)
|
2.
caution |
Do not use special tool oil
pan FIPG cutter (MD998727). The
oil pan lower is made of aluminium and this tool
will damage it.
|
Screw in the bolt into bolt hole A in the location
shown. Then lift the oil pan and remove
it.
|
|
1.Disconnect the steering
shaft assembly and the power steering gear box assembly
(Refer
to GROUP 37 - Power Steering Gear Box and Linkage ).
|
![](../../../img/11/AC502231AB00ENG.png)
|
2.Remove the mounting bolts
of the power steering gear box assembly, and hung the power
steering gear box assembly using a wire or other similar
material (Refer to GROUP 37 - Power
Steering Gear Box and Linkage ).
|
|
1.Remove the hood (Refer to
GROUP 42A - Hood ).
|
![](../../../img/11/ACE02494AB00ENG.png)
![](../../../img/11/ACE02495AB00ENG.png)
|
2.Install special tool
engine hanger plate (MB991956) to the cylinder
head.
|
![](../../../img/11/ACE02498AB00ENG.png)
|
3.
caution |
Disconnect the cables, the
hoses and wiring harness connectors
before holding the engine assembly.
|
Use a chain block to hold the engine assembly. Then
remove the engine mounting bolts (Refer
to ).
|
![](../../../img/11/ACE02428AB00ENG.png)
|
4.Lift the engine assembly.
Then insert a wooden piece (100 x 100 x 25 mm) between the
engine
mounting bracket (chassis frame) and the front engine
support insulator. 5.Secure the engine assembly
with a wooden piece to ensure working space to gain access
to the oil pan upper.
|
|
1.Remove the oil pan
mounting bolts.
|
![](../../../img/11/ACE02394AB00ENG.png)
![](../../../img/11/ACE02483AA00ENG.png)
|
2.
caution |
Do not use special tool oil
pan FIPG cutter (MD998727). The
oil pan lower is made of aluminium and this tool
will damage it.
|
Screw in the bolt into bolt hole A in the location
shown. Then lift the oil pan and remove
it.
|
|
1.Remove all the traces of
sealant adhering to the oil pan and cylinder block using
a remover or others. Then, degrease them.
|
![](../../../img/11/ACE02395AB00ENG.png)
|
2.Apply the sealant without
any gap to the mating surface of oil pan as shown in the
figure,
and install the oil pan to the cylinder
block. Specified sealant: ThreeBond 1217G or
equivalent
note |
Install the oil pan
immediately after applying sealant.
|
3.
caution |
After the installation, until
a sufficient period of time (one hour or
more) elapses, do not apply the engine oil or
water to the sealant application area or start
the engine.
|
Tighten the oil pan mounting bolts to the specified
torque. Tightening
torque:
M6: 11 ± 3
N·m M10: 49 ± 5
N·m
|
|
1.Remove all the traces of
sealant adhering to the oil pan using a remover or others.
Then, degrease them.
|
![](../../../img/11/ACE02396AB00ENG.png)
|
2.Apply the sealant without
any gap to the mating surface of oil pan as shown in the
figure,
and install the oil pan to the cylinder
block. Specified sealant: ThreeBond 1217G or
equivalent
note |
Install the oil pan
immediately after applying sealant.
|
3.
caution |
After the installation, until
a sufficient period of time (one hour or
more) elapses, do not apply the engine oil or
water to the sealant application area or start
the engine.
|
Tighten the oil pan mounting bolts to the specified
torque. Tightening torque: 11 ± 3
N·m
|