|
1.Start the engine and allow
it to warm up until the temperature of the coolant reaches
80 °C to 90 °C.
|
|
2.Remove the oil filler
cap.
|
|
3.Remove the under skid
plate and engine room under cover front.
|
|
4.
warning |
Use care as oil could be
hot.
|
Remove the oil drain plug to drain oil.
|
![](../../../img/12/ACE01737AB00ENG.png)
|
5.Install a new oil drain
plug gasket, and then tighten the drain plug to the
specified
torque. Tightening torque: 39 ± 5
N·m 6.Install the under skid plate
and engine room under cover front.
|
![](../../../img/12/AC903479AA00ENG.png)
|
7.Refill with specified
quantity of oil. Specified Engine
Oil
- ACEA classification:
"For service A1/B1, A3/B3, A3/B4 or A5/B5"
- API classification:
"For service CD or higher"
Total quantity (Includes volume inside oil filter
and oil cooler): 7.4L
note |
Select engine oil of the
proper SAE viscosity number according to the
atmospheric temperature.
|
8.Install the oil filler
cap. 9.Check oil level.
|
|
1.Start the engine and allow
it to warm up until the temperature of the coolant reaches
80 °C to 90 °C.
|
|
2.Remove the oil filler
cap.
|
|
3.Remove the under skid
plate and engine room under cover front.
|
|
4.
warning |
Use care as oil could be
hot.
|
Remove the oil drain plug to drain oil.
|
![](../../../img/12/ACE01737AB00ENG.png)
|
5.Install a new oil drain
plug gasket, and then tighten the drain plug to the
specified
torque. Tightening torque: 39 ± 5
N·m 6.Install the under skid plate
and engine room under cover front.
|
![](../../../img/12/ACA00381AF00ENG.png)
![](../../../img/12/ACE02877AB00ENG.png)
|
7.Refill with specified
quantity of oil. Specified Engine
Oil
- ACEA classification:
"For service C1, C2, C3 or C4"
- JASO classification: "For service DL-1"
Total quantity (Includes volume inside oil filter
and oil cooler):
- <Except vehicles for Russia>
7.4L
- <Vehicles for Russia> 8.4L
note |
Select engine oil of the
proper SAE viscosity number according to the
atmospheric temperature.
|
8.Install the oil filler
cap. 9.Check oil level indicate below maximum
marking. 10.Warm up engine for 10 minutes and wait
for further 10 minutes. 11.Check that the oil
level is between maximum marking and minimum
marking. 12.If no, add the oil until the oil level
gauge indicates between maximum marking and
minimum marking.
|
|
1.Start the engine and allow
it to warm up until the temperature of the coolant reaches
80 °C to 90 °C.
|
|
2.Remove the oil filler
cap.
|
|
3.Remove the under skid
plate and engine room under cover front.
|
|
4.
warning |
Use care as oil could be
hot.
|
Remove the oil drain plug to drain oil.
|
![](../../../img/12/ACE01736AB00ENG.png)
|
5.Install a new oil drain
plug gasket, and then tighten the drain plug to the
specified
torque. Tightening torque: 39 ± 5
N·m 6.Install the under skid plate
and engine room under cover front.
|
![](../../../img/12/AC903479AA00ENG.png)
|
7.Refill with specified
quantity of oil. Specified Engine
Oil
- ACEA classification:
"For service A1/B1, A3/B3, A3/B4 or A5/B5"
- API classification:
"For service CD or higher"
Total quantity (Includes volume inside oil filter
and oil cooler): 6.4L
note |
Select engine oil of the
proper SAE viscosity number according to the
atmospheric temperature.
|
8.Install the oil filler
cap. 9.Check oil level.
|