Code No. P0107: Manifold Absolute Pressure Sensor Circuit Low Input
OPERATION
- A power voltage of 5 V is applied to the manifold absolute pressure sensor power terminal from the engine-ECU connector terminal 5V and earthed to the engine-ECU connector terminal E from the manifold absolute pressure sensor.
- The sensor signal is inputted to the engine-ECU connector terminal MAP from the manifold absolute pressure sensor output terminal.
FUNCTION
- The manifold absolute pressure sensor detects a change in inlet manifold pressure and inputs the signal to the engine-ECU.
- In response to the signal, the engine-ECU corrects the fuel injection amount, etc.
TROUBLE JUDGEMENT
- Engine coolant temperature is more than 0°C at the engine starts.
or
Check Conditions
- More than 8 minutes have passed since the engine starting sequence was completed, when the engine coolant temperature at engine start is less than 0°C.
- Volumetric efficiency is more than 20 %.
Judgement Criterion
- Manifold absolute pressure is 5 kPa or lower for 2 seconds.
FAIL-SAFE AND BACKUP FUNCTION
- Control as if the inlet manifold vacuum pressure is 101 kPa.
PROBABLE CAUSES
- Failed manifold absolute pressure sensor
- Open/short circuit or harness damage in manifold absolute pressure sensor circuit or loose connector contact
|
STEP 1. M.U.T.-III data list
|
|
- Data list reference table (Refer to
).
- Item 8: Manifold absolute pressure sensor
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Voltage measurement at manifold absolute pressure sensor connector (5V line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(3)Check the voltage between the manifold absolute pressure sensor connector (5V line) and body earth. OK: 4.9 - 5.1 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 3.
|
|
|
|
STEP 3. Check of short to earth, and open circuit in 5V line between manifold absolute pressure sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 4. M.U.T.-III data list
|
|
- Data list reference table (Refer to
).
- Item 8: Manifold absolute pressure sensor
|
|
Q.
Is the check result normal?
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
Replace the engine-ECU.
|
|
|
|
STEP 5. Resistance measurement at manifold absolute pressure sensor connector (E line).
|
|
(1)Disconnect the connector, and measure at the wiring harness side.
|
|
(2)Check the resistance between the manifold absolute pressure sensor connector (E line) and body earth. OK: Continuity (2 Ω or less)
|
|
Q.
Is the check result normal?
|
|
Go to Step 7.
|
|
|
|
Go to Step 6.
|
|
|
|
STEP 6. Check of harness damage in E line between manifold absolute pressure sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 4.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 7. Check of harness damage in 5V line between manifold absolute pressure sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 8.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 8. Check of short to earth, open circuit and damage in MAP line between manifold absolute pressure sensor connector and engine-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 9. M.U.T.-III diagnosis code
|
|
- Reconfirmation of diagnosis code.
|
|
Q.
Is diagnosis code set?
|
|
Go to Step 10.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Use Troubleshooting/Inspection Service Points - How to Cope with Intermittent Malfunctions ).
|
|
|
|
STEP 10. Replace the manifold absolute pressure sensor
|
|
- After replacing the manifold absolute pressure sensor, reconfirm whether the diagnosis code is set.
|
|
Q.
Is diagnosis code set?
|
|
Replace the engine-ECU.
|
|
|
|
Check end.
|
|
|