![](../../../img/14/ACC02432AB00ENG.png)
|
1.
caution |
- To reuse the drive belt, draw an arrow
indicating the rotating direction on the
back of the drive belt using chalk to
install the same direction.
- Do not turn the crankshaft
anti-clockwise.
- Be careful not to get your fingers
caught.
|
Set special tool drive belt remover (MB992728)
between the A/C compressor drive belt and the
crankshaft pulley as shown.
note |
Insert the special tool
between the belt and the pulley.
|
|
![](../../../img/14/ACC02433AB00ENG.png)
|
2.Use a tool to rotate the
crankshaft pulley clockwise until the special tool reaches
the bottom of the pulley.
|
![](../../../img/14/ACC02434AB00ENG.png)
|
3.The arrow on the special
tool should point in direction of travel. Then prise off the
A/C compressor drive belt. 4.Rotate the
crankshaft pulley clockwise further to remove the A/C
compressor drive belt. 5.Check the crankshaft
pulley groove for dust or dirt. If it is contaminated, use
an air blower to clean.
|
|
1.Before removing the drive
belt, slightly loosen the mounting nuts of cooling fan
clutch and water pump pulley.
|
![](../../../img/14/AC508382AB00ENG.png)
|
2.
caution |
To reuse the power steering
belt, draw an arrow indicating the rotating
direction (clockwise) on the back of the power
steering belt using chalk, etc.
|
Loosen the mounting bolts shown in the figure to
remove the drive belt.
|
![](../../../img/14/AC507896AB00ENG.png)
|
1.Loosen the nut for
alternator pivot bolt and locking bolt. 2.
caution |
To reuse the drive belt, draw
an arrow indicating the rotating direction (to
the right) on the back of the belt using chalk,
etc.
|
Turn the adjusting bolt anti-clockwise (in left
turn), and remove the drive belt.
|
|
Temporarily tighten the mounting
nuts of the cooling fan clutch and water pump pulley, and
install the power steering belt. Then, tighten the mounting
nuts to the specified torque.
|
|
Tightening torque: 11
± 1 N·m
|
|
1.
caution |
- To reuse the drive belt, install it by
aligning the arrow mark on the backside
of belt marked at the removal with the
rotating direction.
- Do not turn the crankshaft
anti-clockwise.
|
Engage the A/C compressor drive belt with the
A/C compressor pulley.
|
![](../../../img/14/ACC02435AB00ENG.png)
|
2.Put special tool drive
belt installer (MB992905) on the crankshaft pulley, and then
hook the A/C compressor drive belt onto the projection
of the special tool.
|
![](../../../img/14/ACC02436AB00ENG.png)
|
3.Rotate the special tool to
the direction shown by hand to tension the A/C
compressor drive belt.
|
![](../../../img/14/ACC02437AB00ENG.png)
![](../../../img/14/ACA03702AB00ENG.png)
|
4.Check that the A/C
compressor drive belt is engaged with the grooves in the
crankshaft and the A/C compressor pulleys
correctly.
|
![](../../../img/14/ACC02438AB00ENG.png)
|
5.
caution |
Be careful not to get your
fingers caught.
|
Use a tool to rotate the crankshaft pulley
clockwise. While doing this, be careful that the A/C
compressor drive belt is not twisted or the belt ribs do not
face outwards. Note that the belt is engaged with grooves
in the pulley correctly. 6.On completion, remove
the special tool.
|