Code No. C1782:
SAS Signal Fail
| caution |
- If there is any problem in the
CAN bus lines, an incorrect diagnosis code may be set. Prior to this diagnosis, diagnose the
CAN bus lines (Refer to GROUP 54C -
Troubleshooting
 ).
- Whenever the ECU is replaced, ensure that the CAN bus lines are normal.
- When the steering wheel sensor is replaced, calibrate the steering wheel sensor
(Refer to GROUP 35C -
On-vehicle Service).
- When the ACC/FCM-ECU is replaced, calibrate the radar (refer to ).
|
OPERATION
ACC/FCM-ECU communicates with the steering wheel sensor via the CAN bus lines.
DIAGNOSIS CODE SET CONDITION
This diagnosis code is set when the abnormality below is detected:
- Abnormality in steering wheel sensor signal.
PROBABLE CAUSES
- Malfunction of the CAN bus line
- Malfunction of the column switch assembly (Integrated with steering wheel sensor)
- Malfunction of the ACC/FCM-ECU
|
|
STEP 1. M.U.T.-III CAN bus diagnostics.
|
|
|
Use M.U.T.-III to perform the CAN bus diagnosis.
|
|
|
Q.
Is the check result normal?
|
|
|
 Go to Step 2.
|
|
|
|
|
|
 Repair the CAN bus lines (Refer to GROUP 54C -
Troubleshooting ).
On completion, go to Step 2.
|
|
|
|
|
|
STEP 2. Use M.U.T.-III to confirm a diagnosis code of other systems.
|
|
|
Check if the diagnosis code is set in the steering wheel sensor (Refer to GROUP 35C -
Troubleshooting <Steering
Wheel Sensor>, Diagnosis Function).
|
|
|
Q.
Is the diagnosis code set?
|
|
|
Troubleshoot the steering wheel sensor diagnosis code (Refer to GROUP 35C -
Troubleshooting <Steering
Wheel Sensor>, Diagnosis Code Chart).
|
|
|
|
|
|
Go to Step 3.
|
|
|
|
|
|
STEP 3. Check whether the diagnosis code is set again.
|
|
|
Check again if the diagnosis code is set in the ACC/FCM-ECU.
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
|
(4)Press the ACC ON/OFF switch to turn the ACC system to ON.
|
|
|
(5)On completion, check that the diagnosis code is set again.
|
|
|
Q.
Is diagnosis code No. C1782 set?
|
|
|
Replace the column switch assembly (Integrated with steering wheel sensor) (Refer
to GROUP 54A -
Column Switch). Then go to Step 4.
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Cope with Intermittent
Malfunction).
|
|
|
|
|
|
STEP 4. Check whether the diagnosis code is set again.
|
|
|
Check again if the diagnosis code is set in the ACC/FCM-ECU.
|
|
|
(1)Erase the diagnosis code.
|
|
|
(2)Turn the ignition switch from "LOCK" (OFF) position to "ON" position.
|
|
|
(4)Press the ACC ON/OFF switch to turn the ACC system to ON.
|
|
|
(5)On completion, check that the diagnosis code is set again.
|
|
|
Q.
Is diagnosis code No. C1782 set?
|
|
|
Replace the ACC/FCM-ECU (Refer to ).
|
|
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 -
How to Cope with Intermittent
Malfunction).
|
|
|
|