Code No.P0711:
A/T fluid temperature sensor 1 system (Malfunction)
PROBABLE CAUSES
OPERATION
- The A/T fluid temperature sensor 1 converts
the A/T fluid temperature to voltage, and send the information to the A/T-ECU.
- The A/T fluid temperature rises, the resistance decreases. Thus, the sensor
output voltage depends on the A/T fluid temperature. As the A/T fluid temperature
rises, the output voltage will decrease.
DIAGNOSIS CODE SET CONDITIONS
With driving at the vehicle speed of 40 km/h or more, if the fluid temperature
(fluid temperature sensor 1) is not changed from the status with less than 20°C even
after 10 minutes have elapsed (2 drive cycle), the code No.P0711 is set.
PROBABLE CAUSES
- Malfunction of the A/T fluid temperature sensor 1
- Damaged harness wires and connectors
- Malfunction of the A/T-ECU
|
STEP 1. M.U.T.-III data list
|
|
Item 6: A/T fluid temperature sensor 1 (Refer to Data List Table ).
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 2.
|
|
|
|
STEP 2. Measure the resistance at A/T control solenoid valve
assembly connector.
|
|
Disconnect the connector, and measure the resistance between terminal 14 and 7 at the
sensor side.
|
|
OK:
- Approx. 6.5 Ω (at 10°C)
- Approx. 3.5 Ω (at 25°C)
- Approx. 0.25 Ω (at 110°C)
|
|
Q.
Is the check result normal?
|
|
Go to Step 3.
|
|
|
|
Replace the A/T fluid temperature sensor 1 and solenoid harness.
|
|
|
|
STEP 3. Measure the resistance at A/T control solenoid valve
assembly connector.
|
|
Disconnect the connector, and measure the resistance between terminal GRSE line and earth
at the wiring harness side.
|
|
Q.
Is the check result normal?
|
|
Go to Step 6.
|
|
|
|
Go to Step 4.
|
|
|
|
STEP 4. Check for open circuit in GRSE line between A/T control
solenoid valve assembly connector and A/T-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the connector(s) or wiring harness.
|
|
|
|
STEP 5. Check whether the diagnosis code is set again.
|
|
Check again if the diagnosis code is set.
|
|
Q.
Is diagnosis code No.P0711 set?
|
|
Replace the A/T-ECU.
|
|
|
|
Intermittent malfunction (Refer to GROUP 00 - How to Cope with Intermittent
Malfunction).
|
|
|
|
STEP 6. Measure the voltage at A/T control solenoid valve assembly
connector.
|
|
(1)Disconnect the connector, and measure the voltage between terminal O/TS line and
earth at the wiring harness side.
|
|
(2)Turn the ignition switch to the ON position. OK: 4.5 - 5.1 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Go to Step 7.
|
|
|
|
STEP 7. Measure the voltage at A/T-ECU connector.
|
|
(1)Disconnect A/T control solenoid valve assembly connector.
|
|
(2)Turn the ignition switch to the ON position.
|
|
(3)Measure the voltage between A/T-ECU connector terminal O/TS and earth
at the ECU side. OK: 4.5 - 5.1 V
|
|
Q.
Is the check result normal?
|
|
Go to Step 9.
|
|
|
|
Go to Step 8.
|
|
|
|
STEP 8. Check for short circuit in O/TS line between A/T control
solenoid valve assembly connector and A/T-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|
|
STEP 9. Check for open circuit in O/TS line between A/T control
solenoid valve assembly connector and A/T-ECU connector.
|
|
Q.
Is the check result normal?
|
|
Go to Step 5.
|
|
|
|
Repair the connector(s) or the wiring harness.
|
|
|